How to Measure Windows for Blinds To Go Aventura Installations
Measuring windows correctly is the single most important step when ordering custom window coverings from a regional retailer such as Blinds To Go Aventura. Accurate measurements ensure shades and blinds fit snugly, operate smoothly, and provide the privacy, light control, and aesthetic finish homeowners expect. Whether you’re replacing old treatments or outfitting a new build, the process is straightforward but requires attention to detail: deciding between inside and outside mounts, accounting for obstructions like window cranks and trims, and noting the exact width and height that the manufacturer will use to cut your product. This article walks through practical, shop-tested techniques for measuring a variety of window types commonly found in South Florida homes and condominiums near Aventura, sets out common pitfalls to avoid, and explains what Blinds To Go Aventura technicians will need to ensure a seamless installation.
Inside mount or outside mount: which measurement method matters?
Choosing inside mount versus outside mount is the first decision that affects your measurements. Inside-mount blinds sit within the window frame for a clean, built-in look; outside mounts cover the window frame and often make a small window appear larger. For inside mounts, measure the exact width in three places—top, middle, and bottom—and report the smallest measurement. Do the same for height—measure left, center, and right—and use the largest height so the blind will fully cover the opening. For outside mounts, measure the area you want to cover, including any desired overlap (typically 1–3 inches on each side and 3 inches above the frame) to maximize privacy and light blockage. When ordering from Blinds To Go Aventura, specify inside or outside mount clearly so the factory can apply the correct deductions or add-ons they use during fabrication.
Tools and table: what you need to measure accurately
Gathering the right tools before you begin avoids re-measuring and delays. A steel tape measure is best for accuracy; a level helps confirm squareness; a notepad or phone to record measurements; and a step ladder for high windows. Use the table below as a quick reference when preparing your measurements for Blinds To Go Aventura.
| Tool | Purpose | Tip |
|---|---|---|
| Steel tape measure | Accurate width and height readings | Press tear of tape into corner for exact start point |
| Step ladder | Reach tall or high-set windows | Have a helper hold the tape for safety |
| Level (optional) | Check window frame square | Skewed frames may require custom adjustments |
| Pen and paper / phone | Record measurements and notes | Note inside vs outside mount and any obstructions |
How to measure different window types and common obstructions
Standard rectangular windows are the simplest to measure, but many homes in Aventura have sliding glass doors, arched transoms, casements, or bay windows that require tailored approaches. For sliding glass doors and large windows, measure the width across the whole opening and the height from the top of the frame to the threshold; account for patio track clearance if you’re planning motorized or floor-length treatments. For arched or specialty shapes, measure the widest and tallest straight-line dimensions and photograph the window—Blinds To Go Aventura can advise on the best treatment or whether a custom template is needed. Note obstructions like window cranks, handles, security bars, or trim thickness; for inside mounts, these may prevent a flush fit and could prompt an outside-mount recommendation. When in doubt, take multiple measurements and annotate any irregularities for the showroom consultant or installer.
Avoiding common mistakes: tips from installers
Installers frequently see a handful of repeatable errors: using a cloth tape (which can stretch), measuring frame rather than glass for inside mounts, forgetting to note inside vs outside mount, and failing to check that multiple windows intended to match are truly the same size. Always measure in inches and to the nearest eighth of an inch if possible; record three width and three height measurements for inside mounts and use the smallest and largest as described earlier. If you plan to combine blinds and drapery or add a valance, include the extra width for overlap. For motorized options or smart-home integration available at Blinds To Go Aventura, verify clearance for the motor housing and note any power or battery access points. Clear labeling—window name or room, mount type, width, height—speeds processing and reduces the chance of remakes.
Final checks before ordering and what to expect at installation
Before submitting your order to Blinds To Go Aventura, review each measurement and double-check the mount type, return preference, and control side for cords or wands. If you’re ordering multiple units for consistency, order a sample or schedule an in-home measure if available—many showrooms offer professional measuring services that transfer risk from you to the installer. On installation day, technicians typically verify measurements on-site before any brackets are drilled and will discuss minor adjustments if frames are out of square. A careful measuring process minimizes callbacks and ensures your blinds or shades deliver the intended light control, insulation, and curb appeal in an Aventura residence.
This text was generated using a large language model, and select text has been reviewed and moderated for purposes such as readability.
