Web Results

www.uft.org/.../nyc-building-code-occupant-load-req.pdf

ft. per person for an occupancy is not listed in table 6-2, the occupant load shall be established by an architect or engineer, subject to the approval of the commissioner. (b) Modifications. - (1) When the actual occupant load of any space will be significantly lower than that listed in table 6-2, the commissioner may establish a lower basis ...

www.scribd.com/document/285023760/Occupant-Load-Table-From-IBC

196 Exceptions: 1. Where means of egress from floors above and below converge at an intermediate level.3 Posting of occupant load. only the occupant load of each floor considered individually shall be used in computing the required capacity of the exits at that floor. as applicable in Section 101.2 OCCUPANCY For SI: 1 inch = 25. H-3 and H-4 0.

www.ecodes.biz/ecodes_support/free_resources/2010Florida/Building...

occupant load of less than 50 persons and accessory to another occupancy shall be classified as a Group B occupancy or as part of that occupancy. 3. A room or space used for assembly purposes that is lessthan750squarefeet(70m2)inareaandaccessory to another occupancy shall be classified as a Group B occupancy or as part of that occupancy. 4.

up.codes/viewer/utah/ibc-2015/chapter/10/means-of-egress

The occupant load permitted in any building, or portion thereof, is permitted to be increased from that number established for the occupancies in Table 1004.1.2, provided that all other requirements of the code are met based on such modified number and the occupant load does not exceed one occupant per 7 square feet (0.65 m 2) of occupiable ...

www.reference.com/math/calculate-occupant-load-3a9217907e3...

How Do I Calculate Occupant Load? ... The most recent occupant load factors can be found in Table 1004.1.2 of the 2015 IBC. It's important to consider that some occupant load factors are determined in gross square feet per occupant, but others are determined in net square feet. The gross area of a space is defined as everything within its walls ...

up.codes/s/occupant-load

The occupant load permitted in any building, or portion thereof, is permitted to be increased from that number established for the occupancies in Table 1004.1.2, provided that all other requirements of the code are met based on such modified number and the occupant load does not exceed one occupant per 7 square feet (0.65 m 2) of occupiable ...

totalforcevlc.golearnportal.org/Fire_Inspector_II/Occupant...

to the mercantile occupancy is considered the street floor. d. For any food court or other assembly use areas located in the mall that are not included as a portion of the gross leasable area of the mall building, the occupant load is calculated based on the occupant load factor for that use as specified in Table 7.3.1.2.

www3.iccsafe.org/cs/committeeArea/pdf_file/BU_09_11_11.pdf

“occupancy category” in this section is not the same as the “use and occupancy classification” found in Chapter 3. Even though the “use and occupancy classification” of both buildings may be the same based on Chapter 3, the nature of the occupancy found in Table 1604.5 determines the appropriate “occupancy category” used to ...

poweranddata.info/wp-content/uploads/Codes- California/2013 CBC...

CALIFORNIA BUILDING CODE – MATRIX ADOPTION TABLE CHAPTER 10 – MEANS OF EGRESS (Matrix Adoption Tables are non-regulatory, intended only as an aid to the user. See Chapter 1 for state agency authority and building applications.) ... OCCUPANT LOAD. PANIC HARDWARE. PHOTOLUMINESCENT. PUBLIC WAY. RAMP. SCISSOR STAIR.

www.nyc.gov/html/dob/downloads/bldgs_code/bc27s6.pdf

The occupant load of any space shall include the occupant load of all spaces that discharge through it in order to gain access to an exit. (a) Unlisted occupancies. - Where data regarding the sq. ft. per person for an occupancy is not listed in table 6-2, the occupant load shall be established by an architect or engineer, subject to the ...