Electrical

A:

In order to wire a home light switch you need wire cutters and wire nuts. Start by turning off the power from the circuit breaker, then remove the switch plate, strip and connect the wires and place the new switch in the box.

See Full Answer
Filed Under:
  • How do you install a solar power system for the whole house?

    Q: How do you install a solar power system for the whole house?

    A:

    Estimate the amount of solar panels needed to satisfy the electrical power usage of your home by dividing your average daily energy use by the amount of solar resource available to your region and multiplying that number to adjust it for the efficiency of your panel. Gather your utility bills, and by using a computer, it takes about 30 minutes to calculate the amount of solar panels you need.

    See Full Answer
    Filed Under:
  • Is it safe to plug one power strip into another?

    Q: Is it safe to plug one power strip into another?

    A:

    It is not safe to plug one power strip into another. This is called piggybacking or daisy chaining, and it creates an electrical fire hazard that could prove to be catastrophic.

    See Full Answer
    Filed Under:
  • How can one wire a home light switch?

    Q: How can one wire a home light switch?

    A:

    In order to wire a home light switch you need wire cutters and wire nuts. Start by turning off the power from the circuit breaker, then remove the switch plate, strip and connect the wires and place the new switch in the box.

    See Full Answer
    Filed Under:
  • Where is solar energy being used?

    Q: Where is solar energy being used?

    A:

    While solar energy is used worldwide and even in space, the country with the most installed solar capacity is Germany. According to the European Photovoltaic Industry Association, Germany had approximately 35 GW of installed solar capacity by the end of 2013, almost double its closest competitor. China, Italy, Japan and the United States round out the top five countries with installed solar capacity.

    See Full Answer
    Filed Under:
  • How do you install a fluorescent light fixture?

    Q: How do you install a fluorescent light fixture?

    A:

    Fluorescent light fixtures are produced for both hard ceiling and drop ceiling installations. Installation techniques are different for each type. These instructions focus on installation of fluorescent light fixtures in regular ceilings, with attachment to the framework by wood screws. The process is likely to take an afternoon.

    See Full Answer
    Filed Under:
  • What are some techniques for basic electrical wiring and splicing?

    Q: What are some techniques for basic electrical wiring and splicing?

    A:

    The first step in basic electrical wiring or splicing is to turn off the power to the area in which work is being completed. To ensure safety, it is also important to use a junction box when adding new wires or splicing existing wires.

    See Full Answer
    Filed Under:
  • How deep should electrical lines be buried?

    Q: How deep should electrical lines be buried?

    A:

    Consumer and small commercial electrical lines must be buried between 6 and 24 inches underground, while large commercial and industrial lines must be buried between 30 and 36 feet underground. Electrical lines for carrying current to a home or building must be buried deep enough to avoid digging accidents by homeowners and others.

    See Full Answer
    Filed Under:
  • Why do light bulbs explode?

    Q: Why do light bulbs explode?

    A:

    Exposure to moisture or cold can cause a light bulb to explode. Failure of a light bulb may also be the result of tight screwing or too much electrical flow.

    See Full Answer
    Filed Under:
  • What are the disadvantages of coaxial cable?

    Q: What are the disadvantages of coaxial cable?

    A:

    From a consumer standpoint, the weakest point of coaxial cable is its vulnerability to signal quality loss during use. Factors that determine the magnitude of the signal loss include the length of the cable, wear on the wire and exposure to sources of electromagnetic interference from other electronic devices.

    See Full Answer
    Filed Under:
  • What color are positive and negative wires?

    Q: What color are positive and negative wires?

    A:

    The color of wires is dependent on the method of wiring and where one is located. In the United States, a common two-wire ungrounded circuit has a red positive wire and a black negative wire.

    See Full Answer
    Filed Under:
  • What is the function of a fuse?

    Q: What is the function of a fuse?

    A:

    A fuse prevents an electrical object from receiving too much current. In the event too much electricity is received by an electrical component, the fuse is designed to melt and separate.

    See Full Answer
    Filed Under:
  • What is a double tap in an electrical panel?

    Q: What is a double tap in an electrical panel?

    A:

    According to the Star Tribune, a double tap occurs when two conductors are connected under one screw inside a panelboard. Most circuit breakers do not support double tapping, although some manufacturers, such as like Cutler Hammer, make hardware specially designed for this purpose.

    See Full Answer
    Filed Under:
  • Do you need to be an electrician to wire things?

    Q: Do you need to be an electrician to wire things?

    A:

    Not all jurisdictions require a person to hold a license to perform electrical work, according to the Copper Development Association. Therefore, a non-electrician could potentially perform wiring for another person. A homeowner is typically able to complete minor wiring installations and repairs in a home with necessary permits and inspections.

    See Full Answer
    Filed Under:
  • How do you wire a three-pin plug?

    Q: How do you wire a three-pin plug?

    A:

    The first step in wiring a three-pin plug is to bare the ends of the three wires inside the electrical cord for about ? centimeter by cutting away the plastic insulation, then remove the plug cover. Insert the twisted copper wires into the holes in the pins, ensuring the green and yellow wires go into the top pin, while the blue and brown wires go into the left pin and right pin respectively, then replace the plug cover.

    See Full Answer
    Filed Under:
  • What is a Christmas light fixer?

    Q: What is a Christmas light fixer?

    A:

    A Christmas light fixer is a tool for repairing Christmas decoration lights that won't light up. It is a dedicated tool that features a voltage detector, fuse and bulb testers, bulb remover and a shunt repairer. This tool is available in different designs and colors to suit customers' needs.

    See Full Answer
    Filed Under:
  • What is an E-Z-Go wiring diagram?

    Q: What is an E-Z-Go wiring diagram?

    A:

    E-Z-GO wiring diagrams describe the electrical systems of electric- and gas-powered E-Z-GO golf cars. As of 2014, diagrams for most E-Z-GO models, from 1954 to present day, can be obtained from the manufacturer, various golf-car-related websites and golf-car-parts distributors.

    See Full Answer
    Filed Under:
  • Q: What are some instructions for installing an underground electrical cable?

    A:

    To install an underground electrical cable, dig a trench to the required depth, insert electrical wires in a PVC conduit, lay the cable in the trench, call authorities to inspect the installation, cover the trench with soil, and complete the wiring. Attach plate covers, test the installation, and contact the authorities to inspect the project again. A shovel and adjustable wrench are handy for the installation.

    See Full Answer
    Filed Under:
  • Q: How do you install a 220-volt circuit breaker?

    A:

    Install a 220-volt circuit breaker by turning off the electric power, removing the electrical panel cover, and breaking out the tabs for the slots where you are installing the breaker. Connect the two black wires to the two screws of the new circuit breaker, and rock the breaker back and forth to insert it into the panel. Attach the ground wire to the ground bar in the panel, and tighten the screw.

    See Full Answer
    Filed Under:
  • Q: How deep should you bury electrical wire?

    A:

    The National Electric Code requires that wire placed in Schedule 80 PVC must be buried at least 18 inches below ground. If the wire is being buried without PVC, it must be at least 24 inches underground.

    See Full Answer
    Filed Under:
  • Q: Does the Meyer Plows website contain wiring schematic information?

    A:

    Visitors to MeyersProducts.com find wiring schematic information for some Meyer plows by clicking the Owner's Manuals link under the Support heading at the top of the home page. Visitors select the Snow Plow Manuals link under the Meyer Owner's Manual Center heading.

    See Full Answer
    Filed Under:
  • Q: How do you make an online payment to Con Edison?

    A:

    Online payments to Con Edison are processed through the My Account service center located on the company website. The My Account service center allows users to pay bills, view account information, submit meter readings and locate past bills.

    See Full Answer
    Filed Under:

Explore Home Maintenance