Woodturning

Woodturning

Woodturning is a form of woodworking that is used to create wooden objects on a lathe. Woodturning differs from most other forms of woodworking in that the wood is moving while a (relatively) stationary tool is used to cut and shape it. Many intricate shapes and designs can be made by turning wood.

There are two distinct methods of turning wood: spindle turning and faceplate turning. In spindle turning, the grain of the wood runs lengthwise, parallel to the bed of the lathe. In face plate turning, the grain of the wood runs perpendicular to the axis of rotation. Most bowls, platters and many vessels are face plate turned. Pens, furniture legs, spindles, and some vessels are spindle turned. It is the orientation of the grain that determines the method in use. Spindle turning is named for the type of product originally produced, while faceplate turning is named for an early method of attaching the material to the lathe.

The distinction between spindle turning and faceplate turning is due to the fibrous nature of the material. When wood is cut in such a way that the fiber being cut is not supported by the fiber below it, it tends to separate and tear. This "tearout" exhibits a rough, highly undesirable surface texture and greatly reduces the value of any product exhibiting it. The direction of cut is different in spindle turning and faceplate turning because cutting in the wrong direction can cause tearout. Spindle turning cuts are made from high points toward the axis on the outside of the piece, and from the axis toward the outside when hollowing. When faceplate turning, the opposite applies.

History

The origin of woodworking dates to around 1300BC when the Egyptians first developed a two-person lathe. One person would turn the wood with a rope while the other used a sharp tool to cut shapes in the wood. The Romans improved the Egyptian design with the addition of a turning bow. Early bow lathes were also developed and used in Germany, France and Britain. In the Middle Ages a pedal replaced hand-operated turning, freeing both the craftsman's hands to hold the woodturning tools. The pedal was usually connected to a pole, often a straight-grained sapling. The system today is called the "spring pole" lathe (see Polelathe). Spring pole lathes were in common use into the early 20th Century. A two-person lathe, called a "great lathe", allowed a piece to turn continuously (like today's power lathes). A master would cut the wood while an apprentice turned the crank.

The term "bodger" stems from pole lathe turners who used to make the chair legs and spindles. A bodger would typically purchase all the trees on a plot of land, set up camp on the plot, and then fell the trees and turn the wood. The spindles and legs that were produced were sold in bulk, for pence per dozen. The bodger's job was considered unfinished because he only made component parts. The term now describes a person who leaves a job unfinished, or does it badly.

During the industrial revolution the lathe was motorized, allowing turned items to be created in less time. The motor also produced a greater rotational speed for the wood, making it easier to quickly produce high quality work. Today most commercial woodturning is done by computer-operated machinery allowing for mass-production that can be created with accurate precision and without the cost of employing craftsmen. Despite this, there is still a demand for hand-turned products. Woodturning is also a hobby enjoyed by many people.

Modern professional woodturners are typically either "production" turners producing large quantities of functional pieces, or artistic turners producing smaller numbers of pieces, often enhanced after turning by carving, piercing, coloring, applying pyrography, gilding, or a number of other techniques to produce objects for the art market.

Common woodturned items

  • Furniture parts - spindles, table legs, stretchers, finials, or other furniture parts
  • Bowls - vessels with a large opening on top
  • Platters and serving trays
  • Pens, mechanical pencils, keyrings and other small items
  • Hollow forms - similar to bowls, except usually taller and with a small opening, when compared to the hollow interior
  • Pepper mills and candlesticks
  • Chess pieces (some cutting may be required after turning, depending on design)
  • Sculptural forms
  • Pool cues
  • Tool handles, especially those for files and lathe tools
  • Baseball bats

Woodturning tools

Turning tools are generally made from three different types of steel, Carbon steel, High speed steel (HSS), and more recently Powdered Metal. Comparing the three types, high speed steel tools maintain their edge longer, requiring less frequent sharpening than carbon steel, but not as long as powdered metal tools. The harder the type of high speed steel used, the longer the edge will maintain sharpness. Powdered steel is even harder than HSS, but does not take an edge that is as sharp as HSS. Unlike other edged woodworking tools, woodturning tools require more frequent sharpening, because the wood passes at a great speed. To maintain a clean cut, the sharpness of the tools edge must be maintained. The sharpening process requires either skill of the craftsman, or one of the many available sharpening jigs, which facilitate maintaining a specific bevel on the tool.

Types

  • roughing gouge - a wide fluted gouge used to initially round a wooden spindle, and to roughly shape it. Generally not intended for cutting end grain due to the large cut it takes and the relatively weak tang connecting the blade to the handle. Unsafe for making bowls or any faceplate work.
  • spindle gouge or detail gouge - a shallow fluted gouge used to create details on spindles, including beads (raised portions of the turning typically semi-circular in cross section) and coves (relieved portions of the turning).
  • bowl gouge - a deep fluted gouge used to turn the outside and inside of bowls and vessels. Often has a thicker shaft and longer handle than a spindle gouge because it has to cut farther away from the handrest.
  • skew chisel - a wide, steeply pointed chisel with the edge running at an angle to the length of the tool. Used to smooth flat spindles, cut beads, and add details. Skew chisels are only used on spindle work (never on faceplate work) and are honed after sharpening to create a razor edge.
  • parting tool - a pointed tool used to separate (part off) work from the lathe, and to create a straight edge separating large and small diameter sections - wide parting tools also called bedans are used to create evenly sized spindle sections.
  • hollowing tool - many different types of tools used to cut out the deep sections of steep bowls, vases and hollow vessels. Often with very long handles, to maintain enough leverage when working in a deep vessel, far away from the handrest.
  • scraper - a tool that scrapes the wood fibers instead of cutting - these are used to smooth off wooden items cut with other tools, and to shape items that are not possible or difficult to shape with gouges. A sharp scraper has a burr at the edge which cuts the wood, only a dull scraper actually scrapes.
  • bowl saver - a tool used to core out the inside part of a bowl, allowing the waste piece to be used to create a smaller bowl, and to limit the amount of wood chips created when hollowing out a bowl.
  • auger - a drill bit used to drill a hole partway or all the way through a wooden item. For cutting the hole for a lamp cord, or as the first step when hollowing out a bowl or vessel
  • chatter tool - a flexible scraper used to add decorative chatter marks to turned items
  • wire - a simple wire, sometimes with handles attached at either side, for the purpose of burning lines into the piece with friction.
  • there are also several tool types for special purposes, as well as tools that are a combination design of the above tools, i.e. skew/chisel combinations, thread cutting tools, ring cutting tools, medium fluted gouges, etc.

Other techniques

  • eccentric turning - turning a single piece multiple times, upon different axes each time.
  • oval or elliptical turning - turning a piece using an accessory mounted to the headstock that changes the center of rotation of the piece in time with the rotation, so that a cutting tool held in a fixed position on the tool-rest cuts an oval rather than a round path on the workpiece
  • therming - mounting a carrier between centers, and then mounting the small workpiece(s) to the carrier, so that the axis of the headstock/tail-stock does not pass through any of the workpieces, and each workpiece gets cut only on one face. As noted in Wood-turning Methods by Mike Darlow, the etymology of the term "therming" comes via a corruption of the name of the Greek god Hermes, who was often represented as a statue set atop a plinth with a construction characteristic of thermed work.
  • segmented turning - a method of woodturning where the wood blank is constructed from many individual pieces of wood (segments) which are glued together before being turned. Many interesting patterns can be generated through the process of gluing and shaping on the lathe.
  • green or wet turning - turning wood while its moisture content is above equilibrium. Often done when the wood is newly felled. May be turned to finished thickness, in which case the differential shrinkage of the wood will result in a finished piece that is not perfectly round. Alternatively, it may be "rough turned". Rough turning involves turning the piece only to its general shape, leaving enough thickness so that after turning it can be allowed to dry to equilibrium moisture content and distort. The advantage over first drying the wood then turning is that a rough turned piece dries faster, will probably distort instead of split as massive wood is wont to do, and that wet wood turns better, since it creates less dust. Rough turning is inexact science: turning wood too thick will lead to splits, turning wood too thin will lead to distortion that cannot be removed, because not enough thickness is left. Once dry, it is mounted on the lathe a second time and turned to its final form. Rough turning is typically used on most functional work and some artistic pieces.
  • natural edge work - pieces which include the outside of the tree trunk or limb as the edge of the piece. Typically artistic turnings, usually bowls or hollow vessels, and usually green turned to final dimension. May include the bark or not, but pieces with bark should not have any bark damaged or missing.
  • ornamental turning - also known as OT, a method in which the piece is mounted upon a rocking headstock, and a spinning tool is used to cut out exotic and decorative patterns

Safety

When woodturning, it is important to wear certain personal protective equipment (PPE). Loose clothing should not be worn, all jewelry should be removed, and long hair should be tied back. Wood shavings generated during turning will also need to be periodically removed.

  • Eye protection is a necessity when woodturning. There are several PPE available for eye protection such as safety goggles, glasses and visors, some of which feature built-in respirators. Although all of these are adequate, for the highest level of protection, a visor that protects the entire head from dust and debris should be worn.
  • Respiratory equipment and Dust collection systems are also important when woodturning or doing any type of woodworking that creates dust. This can range from a simple disposable dust mask, to a full face helmet with built in respirator. Most stand alone respiratory equipment will interfere with dust shields and visors, so devices that incorporate both are available. Many woods create dust that is actually a health hazard. For example, cocobolo (granadillo) dust is known to be toxic (toxic shock). Many people are sensitive to oils carried in walnut, locust, and oak sawdust.
  • Ear protection Compared to other power tools, a lathe is a relatively quiet machine. Ear protection should be used if noise is excessive, this may be due to motor (fan) noise from a shop dust collector, or the combination of wood and tool being used.
  • Hand/Skin protection Gloves should not be used with rotating equipment, since there's always a risk of getting tangled in the machine. Nevertheless, some woods provide splinters that not only puncture skin, but also cause festering sores and/or skin irritation. Polishes and finishes used in woodturning can also be harmful or irritant to skin, often containing organic solvents such as methanol, turpentine and toluene. This subject continues to be debated in the community.
  • Foot protection. Protective footwear, often leather steel-toe boots, is required for any type of shop activity.

See also

External links

Search another word or see woodturningon Dictionary | Thesaurus |Spanish
Copyright © 2014 Dictionary.com, LLC. All rights reserved.
  • Please Login or Sign Up to use the Recent Searches feature