Lithium-ion_polymer_battery

Lithium-ion polymer battery

Lithium-ion polymer batteries, polymer lithium ion, or more commonly lithium polymer batteries (abbreviated Li-poly, Li-Pol, LiPo, LIP, PLI or LiP) are rechargeable batteries which have technologically evolved from lithium-ion batteries. Ultimately, the lithium-salt electrolyte is not held in an organic solvent as in the lithium-ion design, but in a solid polymer composite such as polyethylene oxide or polyacrylonitrile. The advantages of Li-poly over the lithium-ion design include lower cost manufacturing and being more robust to physical damage. Lithium-ion polymer batteries started appearing in consumer electronics around 1996.

Overview

Cells sold today as polymer batteries have a different design from the older lithium-ion cells. Unlike lithium-ion cylindrical, or prismatic cells, which have a rigid metal case, polymer cells have a flexible, foil-type (polymer laminate) case, but they still contain organic solvent. The main difference between commercial polymer and lithium-ion cells is that in the latter the rigid case presses the electrodes and the separator onto each other, whereas in polymer cells this external pressure is not required because the electrode sheets and the separator sheets are laminated onto each other.

Since no metal battery cell casing is needed, the battery can be lighter and it can be specifically shaped to fit the device it will power. Because of the denser packaging without intercell spacing between cylindrical cells and the lack of metal casing, the energy density of Li-poly batteries is over 20% higher than that of a classical Li-ion battery and they store more energy than nickel-cadmium (NiCd) and nickel metal hydride (NiMH) batteries of the same volume.

The voltage of a Li-poly cell varies from about 2.7 V (discharged) to about 4.23 V (fully charged), and Li-poly cells have to be protected from overcharge by limiting the applied voltage to no more than 4.235 V per cell used in a series combination. Overcharging a Li-poly battery will likely result in explosion and/or fire. During discharge on load, the load has to be removed as soon as the voltage drops below approximately 3.0 V per cell (used in a series combination), or else the battery will subsequently no longer accept a full charge and may experience problems holding voltage under load.

Early in its development, lithium polymer technology had problems with internal resistance. Other challenges include longer charge times and slower maximum discharge rates compared to more mature technologies. Li-poly batteries typically require more than an hour for a full charge. Recent design improvements have increased maximum discharge currents from two times to 15 or even 30 times the cell capacity (discharge rate in amps, cell capacity in amp-hours). In March 2005 Toshiba announced a new design offering a much faster (about 1–3 minutes) rate of charge. These cells have yet to reach the market but are expected to have a dramatic effect on the power tool and electric vehicle industries, and a major effect on consumer electronics.

When compared to the lithium-ion battery, Li-poly has a greater life cycle degradation rate. However, in recent years, manufacturers have been declaring upwards of 500 charge-discharge cycles before the capacity drops to 80% (see Sanyo). Another variant of Li-poly cells, the "thin film rechargeable lithium battery", has been shown to provide more than 10,000 cycles.

Applications

A compelling advantage of Li-poly cells is that manufacturers can shape the battery almost however they please, which can be important to mobile phone manufacturers constantly working on smaller, thinner, and lighter phones. Another advantage of lithium polymer cells over nickel-cadmium and nickel metal hydride cells is that the rate of self-discharge is much lower.

Li-poly batteries are also gaining favor in the world of radio-controlled aircraft as well as Radio-controlled cars, where the advantages of both lower weight and greatly increased run times can be sufficient justification for the price. However, lithium polymer-specific chargers are required to avoid fire and explosion. Explosions can also occur if the battery is short-circuited, as tremendous current passes through the cell in an instant. Radio-control enthusiasts take special precautions to ensure their battery leads are properly connected and insulated. Furthermore fires can occur if the cell or pack is punctured. radio-controlled car batteries are often protected by durable plastic cases to prevent puncture. Specially designed electronic motor speed controls are used to prevent excessive discharge and subsequent battery damage. This is achieved using a low voltage cutoff (LVC) setting that is adjusted to maintain cell voltage greater then (typically) 3 V per cell.

Li-poly batteries are also gaining ground in PDAs and laptop computers, such as Apple's MacBook, MacBook Pro, and Macbook Air, Lenovo's Thinkpad X300 and Ultrabay Batteries, and Dell products featuring D-bay batteries. They can be found in small digital music devices such as iPods and other MP3 players as well as gaming equipment like Sony's Playstation 3 wireless controllers. They are desirable in applications where small form factors and energy density outweigh cost considerations.

These batteries may also power the next generation of battery electric vehicles. The cost of an electric car of this type is prohibitive, but proponents argue that with increased production, the cost of Li-poly batteries will go down.

Technology

There are currently two commercialized technologies, both lithium-ion-polymer (where "polymer" stands for "polymer electrolyte/separator") cells. These are collectively referred to as "polymer electrolyte batteries".

The battery is constructed as:

Typical reaction:

  • Anode: carbon–Lix → C + xLi+ + xe
  • Separator: Li+ conduction
  • Cathode: Li1−xCoO2 + xLi+ + xe → LiCoO2

Polymer electrolytes/separators can be solid polymers (e.g., polyethyleneoxide, PEO) plus LiPF6, or other conducting salts plus SiO2, or other fillers for better mechanical properties (such systems are not available commercially yet). Some manufacturers like Avestor (since merged with Batscap) are using metallic Li as the anode (these are the Lithium-metal-polymer batteries), whereas others wish to go with the proven safe carbon intercalation anode.

Both currently commercialized technologies use PVdF (a polymer) gelled with conventional solvents and salts, like EC/DMC/DEC. The difference between the two technologies is that one (Bellcore/Telcordia technology) uses LiMn2O4 as the cathode, and the other the more conventional LiCoO2.

Other, more exotic (although not yet commercially available) Li-polymer batteries use a polymer cathode. For example, Moltech is developing a battery with a plastic conducting carbon-sulfur cathode. However, as of 2005 this technology seems to have had problems with self-discharge and manufacturing cost.

Yet another proposal is to use organic sulfur-containing compounds for the cathode in combination with an electrically conducting polymer such as polyaniline. This approach promises high power capability (i.e., low internal resistance) and high discharge capacity, but has problems with cycleability and cost.

Prolonging life in multiple cells through cell balancing

Analog front ends that balance cells and eliminate mismatches of cells in series or parallel significantly improve battery efficiency and increase the overall pack capacity. As the number of cells and load currents increase, the potential for mismatch also increases. There are two kinds of mismatch in the pack: State-of-Charge (SOC) and capacity/energy (C/E) mismatch. Though the SOC mismatch is more common, each problem limits the pack capacity (mAh) to the capacity of the weakest cell.

It is important to recognize that the cell mismatch results more from limitations in process control and inspection than from variations inherent in the Lithium Ion chemistry. The use of cell balancing can improve the performance of series connected Li-ion Cells by addressing both SOC and C/E issues. SOC mismatch can be remedied by balancing the cell during an initial conditioning period and subsequently only during the charge phase. C/E mismatch remedies are more difficult to implement and harder to measure and require balancing during both charge and discharge periods.

Cell balancing is defined as the application of differential currents to individual cells (or combinations of cells) in a series string. Normally, of course, cells in a series string receive identical currents. A battery pack requires additional components and circuitry to achieve cell balancing. However, the use of a fully integrated analog front end for cell balancing reduces the required external components to just balancing resistors.

This type of solution eliminates the need for discrete capacitors, diodes and most other resistors to achieve balance.

Battery pack cells are balanced when all the cells in the battery pack meet two conditions:

  • If all cells have the same capacity, then they are balanced when they have the same relative State of Charge (SOC.) In this case, the Open Circuit Voltage (OCV) is a good measure of the SOC. If, in an out of balance pack, all cells can be differentially charged to full capacity (balanced), then they will subsequently cycle normally without any additional adjustments. This is mostly a one shot fix.
  • If the cells have different capacities, they are also considered balanced when the SOC is the same. But, since SOC is a relative measure, the absolute amount of capacity for each cell is different. To keep the cells with different capacities at the same SOC, cell balancing must provide differential amounts of current to cells in the series string during both charge and discharge on every cycle.

References

External links

Search another word or see Lithium-ion_polymer_batteryon Dictionary | Thesaurus |Spanish
Copyright © 2014 Dictionary.com, LLC. All rights reserved.
  • Please Login or Sign Up to use the Recent Searches feature
FAVORITES
RECENT

;