The in-gel digestion primarily comprises the four steps destaining, reduction and alkylation (R&A) of the cysteines in the protein, proteolytic cleavage of the protein and extraction of the generated peptides.
The destaining solution for CBB contains usually the buffer salt ammonium bicarbonate (NH4HCO3) and a fraction of 30%-50% organic solvent (mostly acetonitrile). The hydrophobic interactions between protein and CBB are reduced by the organic fraction of the solution. At the same time diminishes the ionic part of the solution the electrostatic bonds between the dye and the positively charged amino acids of the protein. In contrast to a mixture of water with organic solvent the effectivity of destaining is increased. An increase of temperature promotes the destaining process. To a certain degree (< 10%) the destaining procedure is accompanied with a loss of protein.. Furthermore, the removal of CBB does not affect the yield of peptides in the mass spectrometric measurement.
In the case of silver stained protein bands the destaining is accomplished by oxidation of the metallic silver attached to the protein by potassium ferricyanide or hydrogen peroxide (H2O2). The released silver ions are complexed subsequently by sodium thiosulfate.
This chemical modification allows for proteins with a high number of disulfide bonds the successful identification as well as the highest peptide yield and sequence coverage. Due to the rareness of the aminoacid cysteine for most of the proteins the step of r&a does not effect any improvement of the mass spectrometric analysis. For the quantitative and homogeneous alkylation of cysteines the point of time for the modification is crucial. With denaturing electrophoresis it is strongly recommended to perform the reaction before the execution of the electrophoresis, since there are free acrylamide monomers in the gel able to modify cysteines. The resulting acrylamide adducts are bound irreversible to the cysteines and can not be removed by subsequent r&a. The specific mass of the adduct is 174.05 Da.
An undesirable side effect of the use of proteolytic enzymes is the self digestion of the protease. To avoid this, in the past Ca2+-ions were added to the digestion buffer. Nowadays most suppliers offer modified trypsin where selective methylation of the lysines limits the autolytic activity to the arginine cutting sites. Unmodified trypsin has its highest activity between 35°C and 45°C. After the modification, the optimal temperature is changed to the range of 50°C to 55°C. Other enzymes used for in-gel digestion are the endoproteases Lys-C , Glu-C , and Asp-N. . These proteases cut specifically at only one amino acid e.g. Asp-N cuts n-terminal of aspartic acid. Therefore a lower number of longer peptides is obtained.
The analysis of the complete primary sequence of a protein using only one protease is usually not possible. In those cases the digestion of the target protein in several approaches with different enzymes is recommended. The resulting overlapping peptides permit the assembly of the complete sequence of the protein.
For the digestion the proteins fixed in the matrix of the gel have to be made accessible for the protease. The permeation of the enzyme to the gel is believed to be facilitated by the dehydration of the gel pieces by treatment with acetonitrile and subsequent swelling in the digestion buffer containing the protease. This procedure relies on the presumption that the protease permeates to the gel by the process of swelling. Different studies about the penetration of the enzymes to the gel showed the process to be almost completely driven by diffusion. The drying of the gel does not seam to support the process. Therefore, the improvement of the in-gel digestion has to be achieved by the reduction of the way of the enzyme to its substrate e.g. by cutting the gel to pieces as small as possible.
Usually, the in-gel digestion is run as an overnight process. For the use of trypsin as protease and a temperature of 37°C the time of incubation found in most protocols is 12-15 h. However, experiments about the duration of the digestion process showed that after 3 h there is enough material for successful mass spectrometric analysis. Furthermore, the optimisation of the conditions for the protease in temperature and pH allows for the completion of the digestion of a sample in 30 min.
Surfactant (detergents) can aid in the solubilization and denaturing of proteins in the gel and thereby shorten digestion times and increase protein cleavage and the number and amount of extracted peptides, especially for lipophilic proteins such as membrane proteins. Cleavable detergents are detergents that are cleaved after digestion, often under acidic conditions. This makes the addition of detergents compatible with mass spectrometry.formic acid for ESI and trifluoroacetic acid for MALDI respectively. Studies on model proteins showed a recovery of approximately 70-80% of the expected peptide yield by extraction from the gel. Many protocols contain an additional fraction of acetonitrile to the extraction solution which, in concentrations above 30% (v/v), is effective in reducing the adsorption of peptides to the surface of reaction tubes and pipette tips. The liquid of the pooled extracts is evaporated in a centrifugal evaporator. If the volatile salt ammonium bicarbonate was used for the basic extraction, it is partially removed in the drying process. The dryed peptides can be stored at -20°C for at least six month.
More severe than the difficulties with handling are losses of material while processing the samples. The mass spectrometric protein analysis is often performed at the limit of detection, so even small losses can decide about success or failure of the whole analysis. These losses are due to washout during different processing steps, adsorption to the surface of reaction tubes and pipette tips, uncomplete extraction of peptides from the gel and/or bad ionisation of single peptides in the mass spectrometer. In dependence of the different physicochemical properties of the peptides the losses can vary between 15 and 50%. Due to this heterogeneity of the peptides up to now a universally valid solution for this major drawback of the method has not been found.
The spot picker is programmed with a picking list generated by an gel image analysis software and excises the desired protein spots from a 2D gel. The gel plugs are transferred to a microplate where the digestion robot performs the necessary steps for the in-gel digestion. Afterwards the spotter deposits the peptide solution on MALDI target plates or on microplates for automated ESI-MS measurement. Manufacturers of automated in-gel digestion systems are GE Healthcare (Ettan Series), Bruker Daltonics (PROTEINEER), Perkin Elmer (MultiPROBE II), and Shimadzu (Xcise). The advantages of the automation other than the larger number of spots to be processed at a time are the reduced manual work and the improved standardisation. Due to the many handling steps of the method, the results of the manual process could vary depending on the dexterity of the user and the risk of contamination is high. Therefore, the quality of the results is described to be one main advantage of the automated process.
Drawbacks of automated solutions are the costs for robots, maintenance and consumables as well as the complicated setup of the process. Since the automated picking needs digitised information of the spot location, the analysis of the gel image for relevant spots has to be done by software requiring standardised imaging methods and special scanners. This lengthy procedure prevents the researcher from spontaneous identifications of a few interesting spots from a single gel as well as the need to operate the systems at full capacity. The resulting amount of data from the subsequent automated MS analysis is another problem of high throughput systems as their quality is often questionable and the evaluation of these data takes significantly longer than the collection.
Most of the kit systems are mere collections of the chemicals and enzymes needed for the in-gel digestion whereas the underlying protocol remains unchanged from the manual standard procedure described above. The advantage of these products for the unexperienced customer lies in the guaranteed functioning of the diverse solutions in combination with a ready-made protocol for the process. Suppliers of these kits are Sigma-Aldrich (Trypsin Profile IGD Kit), Pierce (In-Gel Tryptic Digestion Kit), and Agilent (Protein In-gel Tryptic Digestion Kit).
A few companies have tried to improve the handling process of in-gel digestion to allow even with manual sample preparation an easier and more standardised workflow. The MontageTM In-Gel Digest Kit from Millipore is based on the standard protocol, but enables processing of a large number of parallel samples by transferring the handling of the gel pieces to a modified 96 well microplate. The solutions for the diverse steps of in-gel digestion are pipetted into the wells of this plate whereas the removal of liquids is performed through the bottom of the wells by a vacuum pump. This system simplifies the handling of the multiple pipetting steps by the use of multichannel pipettes and even pipetting robots. Actually, some manufacturers of high-throughput systems have adopted the system to work with their robots. This illustrates the orientation of this kit solution to laboratories with a larger number of samples.
A completely different approach is made by the German company OMX GmbH Their product line OMX-S is designed for the small scale use of up to 24 samples at a time by using a shortened protocol and specialised reaction tubes. The product is based on a critical evaluation of the conventional method of in-gel digestion where 30 steps and about 16 hours are needed for the processing from gel spot to peptide solution. The resulting protocol is reduced to four steps and about 2 hours process time by omitting steps not resulting in significant improvement of peptide yield and shortening the incubation time for digestion by increasing the temperature. The reaction tubes provided with this system enable the user to perform all steps from picking the spot to elution of peptides in one device. The gel spot is centrifuged to the reaction chamber through a small opening, a process by which the gel is torn to small pieces. The gel stays for the whole procedure in this reaction chamber, only the different buffers are added by manual pipetting and centrifugation and removed by centrifugation. The handling of in-gel digestion is significantly simplified and acclerated with this system, as well as the risks of contamination and loss of material are reduced. However, the processing of a larger number of samples is due to the manual processing of every single spot still work intensive and not comparable to automated systems.
US Patent Issued to Millipore on Sept. 6 for "Anti-Clogging Device and Method for In-Gel Digestion Applications" (Massachusetts Inventors)
Sep 09, 2011; ALEXANDRIA, Va., Sept. 9 -- United States Patent no. 8,012,434, issued on Sept. 6, was assigned to Millipore Corp. (Billerica,...