Definitions

machinery steel

Thermoforming

[thur-muh-fawrm]

Thermoforming is a manufacturing process for thermoplastic sheet or film. Specifically, it is more of a converting process, where plastic sheet or film is converted into a formed, finished part. The sheet or film is heated in an oven to its forming temperature, then stretched into or onto a mold and cooled. Early generation thermoforming machines usually incorporated cal-rod type heaters, similar to heating elements found in conventional electric kitchen ovens. These are still used, but more modern equipment frequently uses quartz heaters or radiant-panel heaters for more efficient sheet heating and ease of zone control. Cast or machined aluminum is the most common mold material, although epoxy, wood and structural foam are sometimes used for prototypes, samples, and low volume production runs. Aluminum molds are normally water-cooled by a cooling tower or chiller system for faster production capabilities. Thermoforming differs from injection molding, blow molding, rotational molding, and other forms of processing plastics, and is primarily used in the manufacture of disposable cups, containers, lids, trays, blisters, clamshells, and other products. A thermoform machine can utilize vacuum only, or vacuum combined with air pressure, in the forming process. It can be as small and simple as a table-top sample former where small cut sheets of material are placed into a clamp and heated and formed, or as large and complex as a complete inline extrusion, thermoforming, trimming, granulating, and material handling system for continuous high-speed production. Many thermoforming companies do not extrude their own plastic sheet, but rather purchase it in roll-wound form for running on their forming equipment. Others purchase plastic resin in bulk pellet form and extrude the sheet for use on roll-fed or inline forming machines.

There are two main types of trimming used to separate formed plastic parts from the sheet on continuous-forming machinery. Steel rule dies or forged dies are frequently used on inline formers, and the sheet is formed and trimmed on the same machine prior to packing for shipment. "Custom" thermoforming companies usually employ this type trim tooling and process due to frequent job changeovers, short runs, and the relatively low cost of the dies. Higher-volume producers frequently utilize matched-metal punch-and-die trim tooling that operates in a separate trim press machine. In this process, the plastic sheet is formed on a thermoforming machine, then automatically fed into a trim press for cutting. Trim press tooling is many times more expensive than steel-rule or forged dies, so is normally used only for high-volume production.

In the most common method of high-volume, continuous thermoforming, plastic sheet is fed from a roll or from an extruder into a set of indexing chains that incorporate pins, or spikes, that pierce the sheet and transport it through an oven for heating to forming temperature. The heated sheet then indexes into a form station where a mating mold and pressure-box close on the sheet, with vacuum then applied to remove trapped air and to pull the material into or onto the mold along with pressurized air to form the plastic to the detailed shape of the mold. (Plug-assists are typically used in addition to vacuum in the case of taller, deeper-draw formed parts in order to provide the needed material distribution and thicknesses in the finished parts.) A burst of reverse air pressure is actuated from the vacuum side of the mold, commonly referred to as air-eject, as the form tooling opens after forming to break the vacuum and assist the formed parts off of, or out of, the mold. A stripper plate may also be utilized on the mold as it opens for ejection of more detailed parts or those with negative-draft, undercut areas. The sheet containing the formed parts then indexes into a trim station on the same machine, where a die trims the parts from the remaining sheet web. The dies are normally "nicked" in small areas to prevent the formed parts from falling completely out of the sheet after trimming. The formed and trimmed sheet then indexes to a stacker station where tooling automatically strips the formed parts from the sheet web for packing, or for removal by hand from the web if no stacker is used. (For punch-and-die trim press type trimming, the formed sheet would exit the thermoforming machine after the form station and feed into a separate machine for trimming and packing.) The sheet web remaining after the formed parts are trimmed is typically would onto a take-up reel or fed into an inline granulator for recycling.

Most thermoforming companies recycle their scrap and waste plastic, either by compressing in a baling machine or by feeding into a granulator (grinder) and producing ground flake, for sale to reprocessing companies or re-use in their own facility. Frequently, scrap and waste plastic from the thermoforming process is converted back into extruded sheet for forming again.


Thin and thick gauge thermoforming

There are two general thermoforming process categories. Sheet thickness less than 1.5 mm (0.060 inches) is usually delivered to the thermoforming machine from rolls or from a sheet extruder. Thin-gauge roll-fed or inline extruded thermoforming applications are dominated by rigid or semi-rigid disposable packaging. Sheet thicknesses greater than 3 mm (0.120 inches) is usually delivered to the forming machine by hand or an auto-feed method already cut to final dimensions. Heavy, or thick-gauge, cut sheet thermoforming applications are primarily used as permanent structural components. There is a small but growing medium gauge market that forms sheet 1.5 mm to 3 mm in thickness.

Heavy-gauge forming utilizes the same basic process as continuous thin-gauge sheet forming, typically draping the heated plastic sheet over a mold. Many heavy-gauge forming applications use vacuum only in the form process, although some use two halves of mating form tooling and include air pressure to help form. Aircraft windscreens and machine gun turret windows spurred the advance of heavy-gauge forming technology during WWII. Heavy gauge parts are used as cosmetic surfaces on permanent structures such as automobiles, refrigerators, spas, and shower enclosures, and electrical and electronic equipment. Unlike most thin-gauge thermoformed parts, heavy-gauge parts are often hand-worked after forming for trimming to final shape or for additional drilling, cutting, or finishing, depending on the product.

Engineering

Thermoforming has benefited from applications of engineering technology [3], although the basic forming process is very similar to what was invented many years ago. Microprocessor and computer controls on more modern machinery allows for greatly increased process control and repeatability of same-job setups from one production run to the next, usually with the ability to save oven heater and process timing settings between jobs. The ability to place formed sheet into an inline trim station for more precise trim registration has been hugely improved due to the common use of electric servo motors for chain indexing versus air cylinders, gear little bitch in the pondracks, and clutches on older machines. Electric servo motors are also used on some modern and more sophisticated forming machines for actuation of the machine platens where form and trim tooling are mounted, rather than air cylinders which have traditionally been the industry standard, giving more precise control over closing and opening speeds and timing of the tooling. Quartz and radiant-panel oven heaters generally provide more precise and thorough sheet heating over older cal-rod type heaters, and better allow for zoning of ovens into areas of adjustable heatlittle faggots. .

Industry

The more than USD10 billion North American market has traditionally been ¾ thin gauge and ¼ heavy gauge. In 2003 there were about 150 thin gauge thermoformers in North America. Sixty percent formed proprietary products. Thirty percent were custom formers and 10 percent were OEMs with in-house forming capability. There were nearly a dozen thin-gauge formers having annual sales of at least USD100 million. The largest had annual sales in excess of USD1,000 million. There were about 250 heavy gauge formers in North America. Nearly all were custom formers. Only two or three heavy gauge formers had annual sales of more than USD100million. The largest had annual sales of about USD140 million [2].

References

  1. J.L. Throne, Understanding Thermoforming, Hanser Gardner Publications, Inc., Cincinnati OH, 1999.
  2. The Industrial Thermoforming Business: Review and Outlook, Plastics Custom Research Services, Advance NC, 2004.
  3. J.L. Throne, Technology of Thermoforming, Hanser Verlag, Munich, 1996.
  4. Florian, J., "Practical Thermoforming", 1996, ISBN: 0824797620
  5. Gruenwald, G, "Thermoforming: A Plastics Processing Guide", 1998, ISBN: 1566766257

See also

External links

Search another word or see machinery steelon Dictionary | Thesaurus |Spanish
Copyright © 2014 Dictionary.com, LLC. All rights reserved.
  • Please Login or Sign Up to use the Recent Searches feature
FAVORITES
RECENT

;