It is a 2G Mobile Telecommunications Standard that uses CDMA, a multiple access scheme for digital radio, to send voice, data and signaling data (such as a dialed telephone number) between mobile telephones and cell sites.
CDMA or "code division multiple access" is a digital radio system that transmits streams of bits (PN Sequences). CDMA permits several radios to share the same frequencies. Unlike TDMA "time division multiple access", a competing system used in 2G GSM, all radios can be active all the time, because network capacity does not directly limit the number of active radios. Since larger numbers of phones can be served by smaller numbers of cell-sites, CDMA-based standards have a significant economic advantage over TDMA-based standards, or the oldest cellular standards that used frequency-division multiplexing.
It is used in the USA, South Korea, Canada, Mexico, India, Israel, New Zealand, Sri Lanka, Venezuela, Brazil, China PRC and Vietnam. In Q4 2007, around 431 Million subscribers worldwide used CDMA CDMA Development Group, which is about 13 % of the 3,300 Million subscribers in the world. For comparison, of the global subscribers, those using GSM and 3GSM total 2,881 Million GSM World or 86% of the worldwide subscriber base. All other technologies, TDMA (D-AMPS), PDC, iDEN and various older analog systems account for less than 1% of the total worldwide subscriber base. Of the CDMA users, a large number of users come from the USA, South Korea, Vietnam, India, Brazil and China PRC).
P_REV=1 was developed under an ANSI standards process with documentation reference J-STD-008. J-STD-008, published in 1995, was only defined for the then-new North American PCS band (Band Class 1, 1900 MHz). The term IS-95 properly refers to P_REV=1, developed under the Telecommunications Industry Association (TIA) standards process, for the North American cellular band (Band Class 0, 800 MHz) under roughly the same time frame. IS-95 offered interoperation (including handoff) with the analog cellular network. For digital operation, IS-95 and J-STD-008 have most technical details in common. The immature style and structure of both documents are highly reflective of the "standardizing" of Qualcomm's internal project.
P_REV=2 is termed Interim Standard 95A (IS-95A). IS-95A was developed for Band Class 0 only, as in incremental improvement over IS-95 in the TIA standards process.
P_REV=3 is termed Technical Services Bulletin 74 (TSB-74). TSB-74 was the next incremental improvement over IS-95A in the TIA standards process.
P_REV=4 is termed Interim Standard 95B (IS-95B) Phase I, and P_REV=5 is termed Interim Standard 95B (IS-95B) Phase II. The IS-95B standards track provided for a merging of the TIA and ANSI standards tracks under the TIA, and was the first document that provided for interoperation of IS-95 mobile handsets in both band classes (dual-band operation). PREV=4 was by far the most popular variant of IS-95, with P_REV=5 only seeing minimal uptake in South Korea.
P_REV=6 and beyond fall under the CDMA2000 umbrella. Besides technical improvements, the IS-2000 documents are much more mature in terms of layout and content. They also provide backwards-compatibility to IS-95.
In the forward direction, radio signals are transmitted by base stations (BTS's). Every BTS is synchronized with a GPS receiver so transmissions are tightly controlled in time. All forward transmissions are QPSK with a chip rate of 1,228,800 per second. Each signal is spread with a Walsh code of length 64 and a pseudo-random noise code (PN code) of length , yielding a PN roll-over period of ms.
For the reverse direction, radio signals are transmitted by the mobile. Reverse link transmissions are OQPSK in order to operate in the optimal range of the mobile's power amplifier. Like the forward link, the chip rate is 1,228,800 per second and signals are spread with Walsh codes and the pseudo-random noise code, which is also known as a Short Code.
When a mobile is "searching", it is attempting to find pilot signals on the network by tuning to particular radio frequencies, and performing an autocorrelation sweep across all possible PN phases. A strong autocorrelation result indicates the proximity of a BTS.
Other forward channels, selected by their Walsh code, carry data from the network to the mobiles. Data consists of network signaling and user traffic. Generally, data to be transmitted is divided into frames of bits. A frame of bits is passed through a convolutional encoder, adding forward error correction redundancy, generating a frame of symbols. These symbols are then spread with the Walsh and PN sequences and transmitted.
BTS's transmit a sync channel spread with Walsh code 32. The sync channel frame is ms long, and its frame boundary is aligned to the pilot. The sync channel continually transmits a single message, the Sync Channel Message, which has a length and content dependent on the P_REV. The message is transmitted 32 bits per frame, encoded to 128 symbols, yielding a rate of 1200 bit/s. The Sync Channel Message contains information about the network, including the PN offset used by the BTS sector.
Once a mobile has found a strong pilot channel, it listens to the sync channel and decodes a Sync Channel Message to develop a highly-accurate synchronization to system time. At this point the mobile knows whether it is roaming, and that it is "in service".
BTS's transmit at least one, and as many as seven, paging channels starting with Walsh code 1. The paging channel frame time is 20 ms, and is time aligned to the IS-95 system (ie. GPS) 2-second roll-over. There are two possible rates used on the paging channel: 4800 bit/s or 9600 bit/s. Both rates are encoded to 19200 symbols per second.
The paging channel contains signaling messages transmitted from the network to all idle mobiles. A set of messages communicate detailed network overhead to the mobiles, circulating this information while the paging channel is free. The paging channel also carries higher-priority messages dedicated to setting up calls to and from the mobiles.
When a mobile is idle, it is mostly listening to a paging channel. Once a mobile has parsed all the network overhead information, it registers with the network, then optionally enters slotted-mode. Both of these processes are described in more detail below.
Since voice and user data are intermittent, the traffic channels support variable-rate operation. Every 20 ms frame may be transmitted at a different rate, as determined by the service in use (voice or data). P_REV=1 and P_REV=2 supported rate set 1, providing a rate of 1200, 2400, 4800, or 9600 bit/s. P_REV=3 and beyond also provided rate set 2, yielding rates of 1800, 3600, 7200, or 14400 bit/s.
For voice calls, the traffic channel carries frames of vocoder data. A number of different vocoders are defined under IS-95, the earlier of which were limited to rate set 1, and were responsible for some user complaints of poor voice quality. More sophisticated vocoders, taking advantage of modern DSPs and rate set 2, remedied the voice quality situation and are still in wide use in 2005.
The mobile receiving a variable-rate traffic frame does not know the rate at which the frame was transmitted. Typically, the frame is decoded at each possible rate, and using the quality metrics of the Viterbi decoder, the correct result is chosen.
Traffic channels may also carry circuit-switch data calls in IS-95. The variable-rate traffic frames are generated using the IS-95 Radio Link Protocol (RLP). RLP provides a mechanism to improve the performance of the wireless link for data. Where voice calls might tolerate the dropping of occasional 20 ms frames, a data call would have unacceptable performance without RLP.
Under IS-95B PREV=5, it was possible for a user to use up to seven supplemental "code" (traffic) channels simultaneously to increase the throughput of a data call. Very few mobiles or networks ever provided this feature, which could in theory offer 115200 bit/s to a user.
After convolution coding and repetition, symbols are sent to a 20 ms block interleaver, which is a 24 by 16 array.
With CDMA, signals that are not correlated with the channel of interest (such as other PN offsets from adjacent cellular base stations) appear as noise, and signals carried on other Walsh codes (that are properly time aligned) are essentially removed in the de-spreading process. The variable-rate nature of traffic channels provide lower-rate frames to be transmitted at lower power causing less noise for other signals still to be correctly received. These factors provide an inherent lower noise level than other cellular technologies allowing the IS-95 network to squeeze more users into the same radio spectrum.
Active (slow) power control is also used on the forward traffic channels, where during a call, the mobile sends signaling messages to the network indicating the quality of the signal. The network will control the transmitted power of the traffic channel to keep the signal quality just good enough, thereby keeping the noise level seen by all other users to a minimum.
Pacific-East Asian teleconnection. Part II: How the Philippine Sea anomalous anticyclone is established during El Nino development
Nov 15, 2002; Pacific-East Asian Teleconnection. Part II: How the Philippine Sea Anomalous Anticyclone is Established during El Nino...
Wipo Publishes Patent of Huawei Technologies, Li Jun, Zhang Xiaofeng for "Method and Device for Selecting in Multi-Node Computer System Node Where Shared Memory Is Established" (Chinese Inventors)
Sep 02, 2012; GENEVA, Sept. 2 -- Publication No. WO/2012/113224 was published on Aug. 30. Title of the invention: "METHOD AND DEVICE FOR...