The CANDU reactor is a Canadian-invented, pressurized heavy water reactor developed initially in the late 1950s and 1960s by a partnership between Atomic Energy of Canada Limited (AECL), the Hydro-Electric Power Commission of Ontario (now known as Ontario Power Generation), Canadian General Electric (now known as GE Canada), as well as several private industry participants. The acronym "CANDU", a registered trademark of Atomic Energy of Canada Limited, stands for "CANada Deuterium Uranium". This is a reference to its deuterium-oxide (heavy water) moderator and its use of uranium fuel (originally, natural uranium). All current power reactors in Canada are of the CANDU type. Canada markets this power reactor abroad.
The CANDU reactor is conceptually similar to most light water reactors, although it differs in the details.
Fission reactions in the nuclear reactor core heat a fluid, in this case heavy water (see below). This coolant is kept under high pressure to raise its boiling point and avoid significant steam formation in the core. The hot heavy water generated in this primary cooling loop is passed into a heat exchanger heating light water in the less-pressurized secondary cooling loop. This water turns to steam and powers a conventional turbine with a electrical generator attached to it. Any excess heat energy in the steam after flowing through the turbine is rejected into the environment in a variety of ways, most typically into a large body of cool water, such as a lake, river or ocean. Heat can also be disposed of using a cooling tower, but they are avoided whenever possible because they reduce the plant's efficiency. More recently-built CANDU plants, such as the Darlington Nuclear Generating Station near Toronto, Ontario, use a discharge-diffuser system that limits the thermal effects in the environment to within natural variations.
At the time of its design, Canada lacked the heavy industry to cast and machine the large, heavy steel pressure vessel used in most light water reactors. Instead, the pressure is contained in much smaller tubes, 10 cm diameter, that contain the fuel bundles. These smaller tubes are easier to fabricate than a large pressure vessel. In order to allow the neutrons to flow freely between the bundles, the tubes are made of zircaloy, which is highly transparent to neutrons. The zircaloy tubes are surrounded by a much larger low-pressure tank known as a calandria, which contains the majority of the moderator.
Canada also lacked access to uranium enrichment facilities, which were then extremely expensive to construct and operate. The CANDU was therefore designed to use natural uranium as its fuel, like the ZEEP reactor, the first Canadian reactor. Traditional designs using light water as a moderator will absorb too many neutrons to allow a chain reaction to occur in natural uranium due to the low density of active nuclei. Heavy water absorbs fewer neutrons than light water, allowing a high neutron economy that can sustain a chain reaction even in unenriched fuel. Also, the low temperature of the moderator (below the boiling point of water) reduces changes in the neutrons' speeds from collisions with the moving particles of the moderator ("neutron scattering"). The neutrons therefore are easier to keep near the optimum speed to cause fissioning; they have good spectral purity. At the same time, they are still somewhat scattered, giving an efficient range of neutron energies.
The large thermal mass of the moderator provides a significant heat sink that acts as an additional safety feature. If a fuel assembly were to overheat and deform within its fuel channel, the resulting change of geometry permits high heat transfer to the cool moderator, thus preventing the breach of the fuel channel, and the possibility of a meltdown. Furthermore, because of the use of natural uranium as fuel, this reactor cannot sustain a chain reaction if its original fuel channel geometry is altered in any significant manner.
In a traditional light water reactor (LWR) design, the entire reactor core is a single large pressure vessel containing the light water, which acts as moderator and coolant, and the fuel arranged in a series of long bundles running the length of the core. To refuel such a reactor, it must be shut down, the pressure dropped, the lid removed, and a significant fraction of the core inventory, such as one-third, replaced in a batch procedure. The CANDU's calandria-based design allows individual fuel bundles to be removed without taking the reactor off-line, improving overall duty cycle or capacity factor. A pair of remotely-controlled fueling machines visit each end of an individual fuel string. One machine inserts new fuel while the other receives discharged fuel.
A lower 235U density also generally implies that less of the fuel will be consumed before the fission rate drops too low to sustain criticality (due primarily to the relative depletion of 235U compared with the build-up of parasitic fission products). However, by avoiding the uranium enrichment process, overall utilization of mined uranium in CANDU reactors is significantly less than in light-water reactors, about 30-40% less, using current designs.
A CANDU fuel assembly consists of a number of zircaloy tubes containing ceramic pellets of fuel arranged into a cylinder that fits within the fuel channel in the reactor. In older designs the assembly had 28 or 37 half-meter long fuel tubes with 12 such assemblies lying end to end in a fuel channel. The relatively new CANFLEX bundle has 43 tubes, with two pellet sizes. It is about 10 cm (four inches) in diameter, 0.5 m (20 inches) long and weighs about 20 kg (44 lb) and replaces the 37-tube bundle. It has been designed specifically to increase fuel performance by utilizing two different pellet diameters.
A number of distributed light-water compartments called liquid zone controllers help control the rate of fission. The liquid zone controllers absorb excess neutrons and slow the fission reaction in their regions of the reactor core.
CANDU reactors employ two independent, fast-acting safety shutdown systems. Shutoff rods penetrate the calandria vertically and lower into the core in the case of a safety-system trip. A secondary shutdown system involves injecting high-pressure gadolinium nitrate solution directly into the low-pressure moderator.
Compared with light water reactors, a heavy water design is "neutron rich". This makes the CANDU design suitable for "burning" a number of alternative nuclear fuels. To date, the fuel to gain the most attention is mixed oxide fuel (MOX). MOX is a mixture of natural uranium and plutonium, such as that extracted from former nuclear weapons. Currently, there is a worldwide surplus of plutonium due to the various agreements between the United States and the former Soviet Union to dismantle many of their warheads. However, the security of these supplies is a cause for concern. One way to address this security issue is by converting the warhead into fuel and burning the plutonium in a CANDU reactor.
Plutonium can also be extracted from spent nuclear fuel reprocessing. While this consists usually of a mixture of isotopes that is not attractive for use in weapons, it can be used in a MOX formulation reducing the net amount of nuclear waste that has to be disposed of.
Plutonium isn't the only fissile material in spent nuclear fuel that CANDU reactors can utilize. Because the CANDU reactor was designed to work with natural uranium, CANDU fuel can be manufactured from the used (depleted) uranium found in light water reactor (LWR) spent fuel. Typically this "Recovered Uranium" (RU) has a U-235 enrichment of around 0.9%, which makes it unusable to an LWR, but a rich source of fuel to a CANDU (natural uranium has a U-235 abundance of roughly 0.7%). It is estimated that a CANDU reactor can extract a further 30-40% energy from LWR fuel by recycling it in a CANDU reactor.
Recycling of LWR fuel does not necessarily need to involve a reprocessing step. Fuel cycle tests have also included the DUPIC fuel cycle, or direct use of spent PWR fuel in CANDU, where used fuel from a pressurized water reactor is packaged into a CANDU fuel bundle with only physical reprocessing (cut into pieces) but no chemical reprocessing. Again, where light-water reactors require the reactivity associated with enriched fuel, the DUPIC fuel cycle is possible in a CANDU reactor due to the neutron economy which allows for the low reactivity of natural uranium and used enriched fuel.
Several Inert-Matrix Fuels have been proposed for the CANDU design, which have the ability to "burn" plutonium and other actinides from spent nuclear fuel, much more efficiently than in MOX fuel. This is due to the "inert" nature of the fuel, so-called because it lacks uranium and thus does not create plutonium at the same time as it is being consumed.
CANDU reactors can also breed fuel from natural thorium, if uranium is unavailable.
The second CANDU was the Douglas Point reactor, a more powerful version rated at roughly 200 MWe and located near Kincardine, Ontario. Douglas Point went into service in 1968, and ran until 1984. Uniquely among CANDU stations, Douglas Point incorporated an oil-filled window which offered a view of the east reactor face, even when the reactor was operating. The Douglas Point type was exported to India, and was the basis for India's fleet of domestically-designed and built 'CANDU-derivatives'. Douglas Point was originally planned to be a two-unit station, but the second unit was cancelled because of the success of the larger 515 MWe units at Pickering.
In parallel to the development of the classic CANDU heavy-water design, experimental CANDU variants were developed. WR-1, located at the AECL's Whiteshell Laboratories in Pinawa, Manitoba, used vertical pressure tubes and organic oil as the primary coolant. The oil used has a higher boiling point than water, allowing the reactor to operate at higher temperatures and lower pressures than a conventional reactor. This reactor operated successfully for many years, and promised a significantly higher thermal efficiency than water-cooled versions. Gentilly-1, near Trois-Rivières, Québec, was also an experimental version of CANDU, using a boiling light-water coolant and vertical pressure tubes, but was not considered successful and was closed after 7 years of fitful operation.
The successes at NPD and Douglas Point led to the decision to construct the first multi-unit station in Pickering, Ontario. Pickering A, consisting of units 1 to 4, went into service in 1971. Pickering B, consisting of units 5 to 8, went into service in 1983, giving a full-station capacity of 4,120 MWe. The station is placed very close to the city of Toronto, in order to reduce transmission costs.
Pickering A was placed into voluntary lay-up in 1997, as a part of Ontario Hydro's Nuclear Improvement plan. Units 1 and 4 have since been returned to service, although not without considerable controversy regarding significant cost-overruns, especially on Unit 4. (The refurbishment of Unit 1 was essentially on-time and on-budget, accounting for delays in project startup imposed by the Ontario provincial government.)
In 2005, Ontario Power Generation announced that refurbishment of Units 2 and 3 at Pickering A would not be pursued, contrary to expectations. The reason for this change in plan was economic: the material condition of these units was much poorer than had existed for Units 1 and 4, particularly the condition of the steam generators, and thus the refurbishment costs would be much higher. This rendered a return-to-service of Units 2 and 3 uneconomical. A project to decommission these units is currently in the early stages of planning.
However, some of this potential savings is offset by the initial, one time cost of the heavy water. The heavy water required must be more than 99.75% pure and tonnes of this are required to fill the calandria and the heat transfer system. The next generation reactor (the Advanced CANDU Reactor, also called the "ACR") mitigates this disadvantage by having a smaller moderator size and by using light water as a coolant.
Since heavy water is less efficient at transferring energy from neutrons, the moderator volume (relative to fuel volume) is larger in CANDU reactors compared with light-water designs, making a CANDU reactor core generally larger than a light water reactor of the same power output. In turn, this implies higher building costs for standard features like the containment building. This is offset to some degree by the calandria-based construction, but even considering this, the CANDU tends to have higher capital costs compared with other designs. In fact, CANDU plant costs are dominated by construction costs, the price of fuel representing perhaps 10% of the cost of the power it delivers. This is true in general of nuclear plants, where the plant cost and cost of operations represent about 65% of overall lifetime cost. Due to the lower fuelling costs compared to light water reactor designs, the levelized lifetime cost on a "per-kWh" basis tends to be comparable to these other designs.
When first being offered, CANDUs offered much better "running" time statistics, the capacity factor, than light-water reactors of a similar generation. At the time, light-water (LWR) designs spent, on average, about half of their time in maintenance or refueling outages. However, since the 1980s dramatic improvements in LWR outage management have narrowed the gap between LWR and CANDU, with several LWR units achieving capacity factors in the 90% and higher range, with an overall fleet performance of 89.5% in 2005. The latest-generation CANDU 6 reactors have demonstrated an 88-90% capacity factor, but overall fleet performance is dominated by the older Canadian units which generally report capacity factors on the order of 80%.
Some CANDU plants suffered from cost overruns during construction, primarily due to external factors. For instance, a number of imposed construction delays led to roughly a doubling of the projected cost of the Darlington Nuclear Generating Station near Toronto, Ontario. Technical problems and redesigns added about another billion to the resulting $14.4 billion price. In contrast, the two CANDU 6 reactors more recently installed in China at the Qinshan site were completed on-schedule and on-budget, an achievement attributed to tight control over scope and schedule.
Another concern is tritium production. Although heavy water is relatively immune to neutron capture, a small amount of the deuterium turns into tritium via this process. Tritium, when mixed with deuterium, undergoes nuclear fusion more easily than any other elemental mixture. Small amounts of tritium can be used in both the "trigger" of an A-bomb and the "fusion boost" of a boosted fission weapon. Tritium can also be used in the main fusion process of an H-bomb, but in this application it is typically generated in situ by neutron irradiation of lithium-6.
Tritium is extracted from some CANDU plants in operation in Canada, primarily to improve safety in case of heavy-water leakage. The gas is stockpiled and used in a variety of commercial products, notably "powerless" lighting systems and medical devices. In 1985 what was then Ontario Hydro sparked controversy in Ontario due to its plans to sell tritium to the US. The plan, by law, involved sales to non-military applications only, but some speculated that even this minor penetration of the market would aid the U.S. nuclear weapon program. Demands for this supply in the future appear to outstrip production; in particular the needs of future generations of experimental fusion reactors like ITER will use up a significant amount of any potential stockpile. Currently between 1.5 and 2.1 kg of tritium are recovered yearly at the Darlington separation facility, of which a minor fraction is sold.
The 1998 Operation Shakti test series in India included one bomb of about 45 kT yield that India has publicly claimed was a hydrogen bomb. An offhand comment in the BARC publication Heavy Water - Properties, Production and Analysis appears to suggest that the tritium was extracted from the heavy water in the CANDU and PHWR reactors in commercial operation. Janes Intelligence Review quotes the Chairman of the Indian Atomic Energy Commission as admitting to the tritium extraction plant, but refusing to comment on its use. It is known, however, that India has developed the technology to create tritium from the neutron-irradiation of lithium-6 in reactors, a process that is several orders of magnitude more efficient than the extraction of tritium from irradiated heavy water.
CANDU reactors have been proposed as the main vehicle for planned supply replacement and growth in Ontario, Canada, a province that currently generates over 50% of its electricity from CANDU reactors, with Canadian government help with financing. Interest has also been expressed in Western Canada, where CANDU reactors are being considered as heat and electricity sources for the energy-intensive oil sands extraction process, which currently uses natural gas. Energy Alberta Corporation, headquartered in Calgary, announced August 272007 that they had filed application for a license to build a new nuclear plant at Lac Cardinal (30 km west of the town of Peace River, Alberta). The application would see an initial twin AECL ACR-1000 plant go online in 2017, producing 2.2 gigawatt (electric).
Romania is in discussions for the completion of its multi-unit nuclear plant at Cernavoda, now consisting of two operating CANDU reactors. Three more partially-completed CANDU reactors exist on the same site, part of a project discontinued at the close of the Nicolae Ceauşescu regime.
Turkey has repeatedly shown interest in the CANDU reactor, but so far has chosen not to pursue nuclear energy. In the summer of 2006, Turks protested against plans for building nuclear reactors.
The units are designed with a planned operating life of over fifty years, which will be achieved with a mid-life program to replace some of the key components, such as the fuel channels. The plants have a projected average annual capacity factor of more than nintety per cent.
Enhancement of the CANDU 6 design to achieve higher plant output include: the installation of an Ultrasonic Flow Meter (UFM) to improve the accuracy of feedwater flow measurements, improvements in turbine design itself and change in condenser vacuum system design for operation at lower condenser pressures.
AECL continues to develop other features to further improve the plant’s performance while maintaining the basic features of the CANDU 6 design, which over time have proven to be extremely reliable with an excellent production record since the early 1980s. The additional enhancements include:
At the same time the basic and defining design features of CANDU are all maintained:
It is expected that the capital cost of constructing these plants will be reduced by up to 40% compared to current CANDU 6 plants.
Tritium is generated in all nuclear power designs; however, CANDU reactors generate more tritium in their coolant and moderator than light-water designs, due to neutron capture in heavy hydrogen. Some of this tritium escapes into containment and is generally recovered; however a small percentage (about 1%) escapes containment and constitutes a routine radioactive emission from CANDU plants (also higher than from an LWR of comparable size). Operation of a CANDU plant therefore includes monitoring of this effluent in the surrounding biota (and publishing the results), in order to ensure that emissions are maintained below regulatory limits.
In some CANDU reactors the tritium concentration in the moderator is periodically reduced by an extraction process, in order to further reduce this risk. Typical tritium emissions from CANDU plants in Canada are less than 1% of the national regulatory limit, which is based upon the guidelines of the International Commission on Radiological Protection (ICRP) (for example, the maximum permitted drinking water concentration for tritium in Canada, 7000 Bq/L, corresponds to 1/10 of the ICRP's public dose limit). Tritium emissions from other CANDU plants are similarly low.
In general there is significant public controversy associated with radioactive emissions from nuclear power plants, and for CANDU plants one of the main concerns is tritium. In 2007 Greenpeace published a critique of tritium emissions from Canadian nuclear power plants by Dr. Ian Fairlie. This report was reviewed by Dr. Richard Osborne and found to be in significant error.
High temperature lubricants sought for advanced engines. (super-hot heavy duty diesel engine) (Special Report - Synlubes)
Apr 19, 1991; High Temperature Lubricants Sought for Advanced Engines GATHERSBURG, Md. -- Liquid lubricants for tomorrow's super-hot heavy duty...