Added to Favorites

Related Searches

Definitions

Nearby Words

descriptive geometry, branch of geometry concerned with the two-dimensional representation of three-dimensional objects; it was introduced in 1795 by Gaspard Monge. By means of such representations, geometrical problems in three dimensions may be solved in the plane. (Such problems arise in all branches of engineering.) Modern mechanical drawing and architectural drawing are based on the principles of descriptive geometry.

The Columbia Electronic Encyclopedia Copyright © 2004.

Licensed from Columbia University Press

Licensed from Columbia University Press

Descriptive geometry is the branch of geometry which allows the representation of three-dimensional objects in two dimensions, by using a specific set of procedures. The resulting techniques are important for engineering, architecture, design and in art. The theoretical basis for descriptive geometry is provided by planar geometric projections. Gaspard Monge is usually considered the "father of descriptive geometry". He first developed his techniques to solve geometric problems in 1765 while working as a draftsman for military fortifications, and later published his findings. ## Protocols

## Heuristics

### The best direction to view:

## General solutions

Figure 1: Descriptive geometry - skew lines appearing perpendicular

Figure 2: Descriptive geometry - skew lines appear equal length

Figure 3: Descriptive geometry - skew lines appear in specified length ratio
## References

## See also

Monge's protocols allow an imaginary object to be drawn in such a way that it may be 3-D modeled. All geometric aspects of the imaginary object are accounted for in true size/to-scale and shape, and can be imaged as seen from any position in space. All images are represented on a two-dimensional drawing surface.

Descriptive geometry uses the image-creating technique of imaginary, parallel projectors emanating from an imaginary object and intersecting an imaginary plane of projection at right angles. The cumulative points of intersections create the desired image.

- Project two images of an object into mutually perpendicular, arbitrary directions. Each image view accommodates three dimensions of space, two dimensions displayed as full-scale, mutually-perpendicular axes and one as an invisible (point view) axis receding into the image space (depth). Each of the two adjacent image views shares a full-scale view of one of the three dimensions of space.
- Either of these images may serve as the beginning point for a third projected view. The third view may begin a fourth projection, and on ad infinitum. These sequential projections each represent a circuitous, 90° turn in space in order to view the object from a different direction.
- Each new projection utilizes a dimension in full scale that appears as point-view dimension in the previous view. To achieve the full-scale view of this dimension and accommodate it within the new view requires one to ignore the previous view and proceed to the second previous view where this dimension appears in full-scale.
- Each new view may be created by projecting into any of an infinite number of directions, perpendicular to the previous direction of projection. (Envision the many directions of the spokes of a wagon wheel each perpendicular to the direction of the axle.) The result is one of stepping circuitously about an object in 90° turns and viewing the object from each step. Each new view is added as an additional view to an orthographic projection layout display and appears in an "unfolding of the glass box model".

Aside from the Orthographic, six standard principal views (Front; Right Side; Left Side; Top; Bottom; Rear), descriptive geometry strives to yield three basic solution views: the true length of a line (i.e., full size, not foreshortened), the point view (end view) of a line, and the true shape of a plane (i.e., full size to scale, or not foreshortened). These often serve to determine the direction of projection for the subsequent view. By the 90° circuitous stepping process, projecting in any direction from the point view of a line yields its true length view; projecting in a direction parallel to a true length line view yields its point view, projecting the point view of any line on a plane yields the plane's edge view; projecting in a direction perpendicular to the edge view of a plane will yield the true shape (to scale) view. These various views may be called upon to help solve engineering problems posed by solid-geometry principles.

There is heuristic value to studying descriptive geometry. It promotes visualization and spatial analytical abilities, as well as the intuitive ability to recognize the direction of viewing for best presenting a geometric problem for solution. Representative examples:

- Two skew lines (pipes, perhaps) in general positions in order to determine the location of their shortest connector (common perpendicular)
- Two skew lines (pipes) in general positions such that their shortest connector is seen in full scale
- Two skew lines in general positions such the shortest connector parallel to a given plane is seen in full scale (say, to determine the position and the dimension of the shortest connector at a constant distance from a radiating surface)
- A plane surface such that a hole drilled perpendicular is seen in full scale, as if looking through the hole (say, to test for clearances with other drilled holes)
- A plane equidistant from two skew lines in general positions (say, to confirm safe radiation distance?)
- The shortest distance from a point to a plane (say, to locate the most economical position for bracing)
- The line of intersection between two surfaces, including curved surfaces (say, for the most economical sizing of sections?)
- The true size of the angle between two planes

A standard for presenting computer-modeling views analogous to orthographic, sequential projections has not yet been adopted. One candidate for such is presented in the illustrations below. The images in the illustrations were created using three-dimensional, engineering computer graphics.

Three-dimensional, computer modeling produces virtual space "behind the tube", as it were, and may produce any view of a model from any direction within this virtual space. It does so without the need for adjacent orthographic views and therefore renders the circuitous, stepping protocol of Descriptive Geometry obsolete.

General solutions are a class of solutions within descriptive geometry that contain all possible solutions to a problem. The general solution is represented by a single, three-dimensional object, usually a cone, the directions of the elements of which are the desired direction of viewing (projection) for any of an infinite number of solution views.

For example: To find the general solution such that two, unequal length, skew lines in general positions (say, rockets in flight?) appear:

- Equal length
- Equal length and parallel
- Equal length and perpendicular (say, for ideal targeting of at least one)
- Equal to lengths of a specified ratio
- others.

In the examples, the general solution for each desired characteristic solution is a cone, each element of which produces one of an infinite number of solution views. When two or more characteristics of, say those listed above, are desired (and for which a solution exists) projecting in the direction of either of the two elements of intersections (one element, if cones are tangent) between the two cones produces the desired solution view. If the cones do not intersect a solution does not exist. The examples below are annotated to show the descriptive geometric principles used in the solutions. TL = True-Length; EV = Edge View.

Figs. 1-3 below demonstrate (1) Descriptive geometry, general solutions and (2) simultaneously, a potential standard for presenting such solutions in orthographic, multiview, layout formats.

The potential standard employs two adjacent, standard, orthographic views (here, Front and Top) with a standard "folding line" between. As there is no subsequent need to 'circuitously step' 90° around the object, in standard, two-step sequences in order to arrive at a solution view (it is possible to go directly to the solution view), this shorter protocol is accounted for in the layout. Where the one step protocol replaces the two-step protocol, "double folding" lines are used. In other words, when one crosses the double lines he is not making a circuitous,90° turn but a non-orthodirectional turn directly to the solution view. As most engineering computer graphics packages automatically generates the six principal views of the glass box model, as well as an isometric view, these views are sometimes added out of heuristic curiosity.

Figure 1: Descriptive geometry - skew lines appearing perpendicular

Figure 2: Descriptive geometry - skew lines appear equal length

Figure 3: Descriptive geometry - skew lines appear in specified length ratio

Wikipedia, the free encyclopedia © 2001-2006 Wikipedia contributors (Disclaimer)

This article is licensed under the GNU Free Documentation License.

Last updated on Wednesday February 20, 2008 at 05:27:44 PST (GMT -0800)

View this article at Wikipedia.org - Edit this article at Wikipedia.org - Donate to the Wikimedia Foundation

This article is licensed under the GNU Free Documentation License.

Last updated on Wednesday February 20, 2008 at 05:27:44 PST (GMT -0800)

View this article at Wikipedia.org - Edit this article at Wikipedia.org - Donate to the Wikimedia Foundation

Copyright © 2014 Dictionary.com, LLC. All rights reserved.