This article is about the electronic device, not an evacuated pipe used for experiments in free-fall.
In electronics, a vacuum tube, electron tube (in North America), thermionic valve, or just valve (elsewhere, especially in Britain) is a device used to amplify, switch, otherwise modify, or create an electrical signal by controlling the movement of electrons in a low-pressure space. Some special function vacuum tubes are filled with low-pressure gas: these are so-called soft valves (or tubes), as distinct from the hard vacuum type which have the internal gas pressure reduced as far as possible. Almost all depend on the thermal emission of electrons, hence thermionic.
Vacuum tubes were critical to the development of electronics technology, which drove the expansion and commercialization of radio broadcasting, television, radar, sound reproduction, large telephone networks, analog and digital computers, and industrial process control. Some of these applications pre-dated electronics, but it was the vacuum tube that made them widespread and practical.
For most purposes, the vacuum tube has been replaced by solid-state devices such as transistors and solid-state diodes. Solid-state devices last much longer, are smaller, more efficient, more reliable, and cheaper than equivalent vacuum tube devices. However, tubes are still used in specialized applications: for engineering reasons, as in high-power radio frequency transmitters; or for their aesthetic appeal, as in audio amplification. Cathode ray tubes are still used as display devices in television sets, video monitors, and oscilloscopes, although they are being replaced by LCDs and other flat-panel displays. A specialized form of the electron tube, the magnetron, is the source of microwave energy in microwave ovens and some radar systems.
A vacuum tube consists of electrodes in a vacuum in a (usually tubular) insulating heat-resistant envelope. Many tubes have glass envelopes, though some types such as power tubes may have ceramic or metal envelopes. The electrodes are attached to leads which pass through the envelope via an airtight seal. On most tubes, the leads are designed to plug into a tube socket for easy replacement.
The simplest vacuum tubes resemble incandescent light bulbs in that they have a filament sealed in a glass envelope which has been evacuated of all air. When hot, the filament releases electrons into the vacuum: a process called thermionic emission. The resulting negatively-charged cloud of electrons is called a space charge. These electrons will be drawn to a metal plate inside the envelope, if the plate (also called the anode) is positively charged relative to the filament (or cathode). The result is a flow of electrons from filament to plate. This cannot work in the reverse direction because the plate is not heated and does not emit electrons. This very simple example described can thus be seen to operate as a diode: a device that conducts current only in one direction. The vacuum tube diode conducts conventional current from plate (anode) to the filament (cathode); this is the opposite direction to the flow of electrons (called electron current).
Vacuum tubes require a large temperature difference between the hot cathode and the cold anode. Because of this, vacuum tubes are inherently power-inefficient; enclosing the tube within a heat-retaining envelope of insulation would allow the entire tube to reach the same temperature, resulting in electron emission from the anode that would counter the normal one-way current flow. Because the tube requires a vacuum to operate, convection cooling of the anode is typically not possible. Instead anode cooling occurs primarily through black-body radiation and conduction of heat to the outer glass envelope via the anode mounting frame. Cold cathode tubes do exist but are used primarily in lighting systems, where unidirectional power regulation is not the functional purpose of the tube.
The vacuum tube is a voltage-controlled device, with the relationship between the input and output circuits determined by a transconductance function. The solid-state device most closely analogous to the vacuum tube is the JFET, although the vacuum tube typically operates at far higher voltage (and power) levels than the JFET.
The 19th century saw increasing research with evacuated tubes, such as the Geissler and Crookes tubes. Scientists who experimented with such tubes included Eugen Goldstein, Nikola Tesla, Johann Wilhelm Hittorf, Thomas Edison, and many others. These tubes were mostly for specialized scientific applications, or were novelties, with the exception of the light bulb. The groundwork laid by these scientists and inventors, however, was critical to the development of vacuum tube technology.
Though the thermionic emission effect was originally reported in 1873 by Frederick Guthrie, it is Thomas Edison's 1884 investigation of the "Edison Effect" that is more often mentioned. Edison patented what he found, but he did not understand the underlying physics, or the potential value of the discovery.
The English physicist John Ambrose Fleming worked as an engineering consultant for technology firms, including Edison Telephone; in 1904, as a result of experiments conducted on Edison Effect bulbs imported from the USA and while working as scientific adviser to the Marconi company, he developed a device he called an "oscillation valve" (because it passes current in only one direction) or kenotron, which can also be used as part of a radio wave detector. Later known as the Fleming valve and then the diode, it allowed electrical current to flow in only one direction, enabling the rectification of alternating current.
In 1906 Robert von Lieben filed for a three electrode amplifying vacuum tube. His invention included also a beam focusing electromagnet.
In 1907 Lee De Forest placed a bent wire serving as a screen, later known as the "grid" electrode, between the filament and plate electrode. As the voltage applied to the grid was varied from negative to positive, the number of electrons flowing from the filament to the plate would vary accordingly. Thus the grid was said to electrostatically "control" the plate current. The resulting three-electrode device was therefore an excellent and very sensitive amplifier of voltages. DeForest called his invention the "Audion". In 1907, DeForest filed for a three-electrode version of the Audion for use in radio communications. The device is now known as the triode. De Forest's device was not strictly a vacuum tube, but clearly depended for its action on ionisation of the relatively high levels of gas remaining after evacuation. The De Forest company, in its Audion leaflets, warned against operation which might cause the vacuum to become too hard. The Finnish inventor Eric Tigerstedt significantly improved on the original triode design in 1914, while working on his sound-on-film process in Berlin, Germany. The first true vacuum triodes were the Pliotrons developed by Irving Langmuir at the General Electric research laboratory (Schenectady, New York) in 1915. Langmuir was one of the first scientists to realize that a harder vacuum would improve the amplifying behaviour of the triode. Pliotrons were closely followed by the French 'R' Type which was in widespread use by the allied military by 1916. These two types were the first true vacuum tubes. Historically, vacuum levels in production vacuum tubes typically ranged between 10 µPa to 10 nPa.
The non-linear operating characteristic of the triode caused early tube audio amplifiers to exhibit harmonic distortions at low volumes. This is not to be confused with the overdrive that tube amplifiers exhibit at high volume levels (known as the tube sound). To remedy the low-volume distortion problem, engineers plotted curves of the applied grid voltage and resulting plate currents, and discovered that there was a range of relatively linear operation. In order to use this range, a negative voltage had to be applied to the grid to place the tube in the "middle" of the linear area with no signal applied. This was called the idle condition, and the plate current at this point the "idle current". Today this current would be called the quiescent or standing current. The controlling voltage was superimposed onto this fixed voltage, resulting in linear swings of plate current for both positive and negative swings of the input voltage. This concept was called grid bias.
When triodes were first used in radio transmitters and receivers, it was found that they had a tendency to oscillate due to parasitic anode-to-grid capacitance. Many circuits were developed to reduce this problem (e.g. the Neutrodyne amplifier), but proved unsatisfactory over wide ranges of frequencies. It was discovered that the addition of a second grid, located between the control grid and the plate and called a screen grid could solve these problems. A positive voltage slightly lower than the plate voltage was applied to it, and the screen grid was bypassed (for high frequencies) to ground with a capacitor. This arrangement decoupled the anode and the first grid, completely eliminating the oscillation problem. An additional side effect of this second grid is that the Miller capacitance is also reduced, which improves gain at high frequency. This two-grid tube is called a tetrode, meaning four active electrodes.
However, the tetrode has some new problems. In any tube, electrons strike the anode hard enough to knock out secondary electrons. In a triode these (less energetic) electrons cannot reach the grid or cathode, and are re-captured by the anode. But in a tetrode, they can be captured by the second grid, reducing the plate current and the amplification of the circuit. Since secondary electrons can outnumber the primary electrons, in the worst case, particularly when the plate voltage dips below the screen voltage, the plate current can actually go down with increasing plate voltage. This is the "tetrode kink" (see the reference for a plot of this effect in the RCA-235 tetrode). Another consequence of this effect is that under severe overload, the current collected by the screen grid can cause it to overheat and melt, destroying the tube.
Again the solution was to add another grid, called a suppressor grid. This third grid was biased at either ground or cathode voltage and its negative voltage (relative to the anode) electrostatically suppressed the secondary electrons by repelling them back toward the anode. This three-grid tube is called a pentode, meaning five electrodes.
Frequency conversion can be accomplished by various methods in superheterodyne receivers. Tubes with 5 grids, called pentagrid converters, were generally used, although alternatives such as using a combination of a triode with a hexode were also used. Even octodes have been used for frequency conversion. The additional grids are either control grids, with different signals applied to each one, or screen grids. In many designs a special grid acted as a second 'leaky' plate to provide a built-in oscillator, which then coupled this signal with the incoming radio signal. These signals create a single, combined effect on the plate current (and thus the signal output) of the tube circuit. The heptode, or pentagrid converter, was the most common of these. 6BE6 is an example of a heptode (note that the first number in the tube ID indicates the filament voltage).
To reduce the cost and complexity of radio equipment, by 1940 it was common practice to combine more than one function, or more than one set of elements in the bulb of a single tube. The only constraint was where patents, and other licencing considerations required the use of multiple tubes. See British Valve Association.
For example, the RCA Type 55 was a double diode triode used as a detector, automatic gain control rectifier and audio preamp in early AC powered radios. The same set of tubes often included the 53 Dual Triode Audio Output.
Another early type of multi-section tube, the 6SN7, is a "dual triode" which, for most purposes, can perform the functions of two triode tubes, while taking up half as much space and costing less.
The invention of the 9-pin miniature tube base, besides allowing the 12AX7 family, also allowed many other multi section tubes, such as the 6GH8 triode pentode. Along with a host of similar tubes, the 6GH8 was quite popular in television receivers. Some color TV sets used exotic types like the 6JH8 which had two plates and beam deflection electrodes (known as 'sheet beam' tube). Vacuum tubes used like this were designed for demodulation of synchronous signals, an example of which is color demodulation for television receivers.
The desire to include many functions in one envelope resulted in the General Electric Compactron. A typical unit, the 6AG11 Compactron tube contained two triodes and two diodes, but many in the series had triple triodes.
An early example of multiple devices in one envelope was the Loewe 3NF. This 1920s device had 3 triodes in a single glass envelope together with all the fixed capacitors and resistors required to make a complete radio receiver. As the Loewe set had only one tubeholder, it was able to substantially undercut the competition since, in Germany, state tax was levied by the number of tubeholders. However, reliability was compromised, and production costs for the tube were much greater.
Loewe were to also offer the 2NF (two tetrodes plus passive components) and the WG38 (two pentodes, a triode and the passive components).
The beam power tube is usually a tetrode with the addition of beam-forming electrodes, which take the place of the suppressor grid. These angled plates focus the electron stream onto certain spots on the anode which can withstand the heat generated by the impact of massive numbers of electrons, while also providing pentode behavior. The positioning of the elements in a beam power tube uses a design called "critical-distance geometry", which minimizes the "tetrode kink", plate-grid capacitance, screen-grid current, and secondary emission effects from the anode, thus increasing power conversion efficiency. The control grid and screen grid are also wound with the same pitch, or number of wires per inch. Aligning the grid wires also helps to reduce screen current, which represents wasted energy. This design helps to overcome some of the practical barriers to designing high-power, high-efficiency power tubes. 6L6 was the first popular beam power tube, introduced by RCA in 1936. Corresponding tubes in Europe were the KT66, KT77 and KT88 by GEC (the KT standing for "Kinkless Tetrode").
Variations of the 6L6 design are still widely used in guitar amplifiers, making it one of the longest lived electronic device families in history. Similar design strategies are used in the construction of large ceramic power tetrodes used in radio transmitters.
Some special-purpose tubes are constructed with particular gases in the envelope. For instance, voltage regulator tubes contain various inert gases such as argon, helium or neon, and take advantage of the fact that these gases will ionize at predictable voltages. The thyratron is a special-purpose tube filled with low-pressure gas or mercury, some of which vaporizes. Like other tubes, it contains a hot cathode and an anode, but also a control electrode, which behaves somewhat like the grid of a triode. When the control electrode starts conduction, the gas ionizes, and the control electrode no longer can stop current flow; the tube "latches" into conduction. Removing plate (anode) voltage lets the gas de-ionize, restoring its non-conductive state. Some thyratrons can carry relatively large currents for their physical size. One example is the miniature type 2D21, often seen in 1950s jukeboxes as control switches for relays. A cold-cathode version of the thyratron, which uses a pool of mercury for its cathode, is called an Ignitron (tm). It can switch thousands of amperes in its largest versions. Thyratrons containing hydrogen have a very consistent time delay between their turn-on pulse and full conduction, and have long been used in radar transmitters. Thyratrons behave much like silicon controlled rectifiers.
Tubes usually have glass envelopes, but metal, fused quartz (silica), and ceramic are possible choices. The first version of the 6L6 used a metal envelope sealed with glass beads, while a glass disk fused to the metal was used in later versions. Metal and ceramic are used almost exclusively for power tubes above 2 kW dissipation. The nuvistor is a tiny tube made only of metal and ceramic. In some power tubes, the metal envelope is also the anode. 4CX800A is an external anode tube of this sort. Air is blown through an array of fins attached to the anode, thus cooling it. Power tubes using this cooling scheme are available up to 150 kW dissipation. Above that level, water or water-vapor cooling are used. The highest-power tube currently available is the Eimac 8974, a forced water-cooled power tetrode capable of dissipating 1.5 megawatts. (By comparison, the largest power transistor can only dissipate about 1 kilowatt.) A pair of 8974s is capable of producing 2 megawatts of audio power. The 8974 is used only in military and commercial radio-frequency installations.
Batteries provided the voltages required by tubes in early radio sets. As many as three different voltages were required, using three different batteries. The "A" batteries or LT (low-tension) battery provided the filament voltage. These were often rechargeable lead-acid type ranging from 2 to 12 volts, with single, double and triple cell batteries being most common. Because these batteries produced 2 V, 4 V or 6 V, tube heaters were designed to operate at those voltages. In portable radios, flashlight (torch) dry batteries were sometimes used.
The plate voltage was provided by "B" batteries or the HT (high-tension) supply or battery. These were generally of dry cell construction, containing many small 1.5 volt cells in series. They typically came in ratings of 22.5, 45, 67.5, 90 or 135 volts.
As a cost reduction measure, especially in high-volume consumer receivers, all the tube heaters could be connected in series across the AC supply, and the plate voltage was derived from a full-wave rectifier directly connected to the AC input, eliminating the need for a heavy transformer. While this limited the plate voltage (and so, indirectly, the output power) that could be obtained, the resulting supply was adequate for many purposes. A filament tap on the rectifier tube provided the 6 volt, low current supply needed for a dial light. These radios could be operated on AC or DC. The so-called series string approach did have one safety defect: the chassis of the receiver was connected to one side of the power supply, presenting a shock hazard. Engineers reduced this hazard by enclosing the chassis in a plastic case, making the back out of particle board, and riveting the power cord chassis plug to the back so that consumers would not be able to power the radio while the chassis was accessible. (Technicians and tinkerers routinely bypassed this by using a separate cord, known colloquially as a "cheater cord" or "widowmaker.") Most consumer AM radio manufacturers of the era used a virtually identical circuit with the tube complement of 12BA6, 12BE6, 12AV6, 35W4, and 50C5, giving these radios the nickname "All American Five," or simply "Five Tube Radio." Tens of millions of such receivers were produced, and they are quickly becoming collector's items.
It became common to use the filament to heat a separate electrode called the cathode, and to use this cathode as the source of electron flow in the tube rather than the filament itself. This minimized the introduction of hum when the filament was energized with alternating current. In such tubes, the filament is called a heater to distinguish it as an inactive element. Development of vacuum tubes that could use alternating current for the heater supply allowed elimination of one rectifier element.
The chief reliability problem of a tube is that the filament or cathode is slowly "poisoned" by atoms from other elements in the tube, which damage its ability to emit electrons. Trapped gases or slow gas leaks can also damage the cathode or cause plate-current runaway due to ionization of free gas molecules. Vacuum hardness and proper selection of construction materials are the major influences on tube lifetime. Depending on the material, temperature and construction, the surface material of the cathode may also diffuse onto other elements. The resistive heaters that heat the cathodes may break in a manner similar to incandescent lamp filaments, but rarely do, since they operate at much lower temperatures than lamps. The heater's failure mode, due to its positive temperature coefficient, is generally associated with the power-up period as a result of the switch-on current surge. A negative temperature coefficient device, such as a thermistor, was sometimes incorporated in the equipment heater supply to compensate.
Another important reliability problem is caused by air leakage into the tube. Usually oxygen in the air reacts chemically with the hot filament or cathode, quickly ruining it. Designers developed tube designs that sealed reliably. This was why most tubes were constructed of glass. Metal alloys (such as Cunife and Fernico) and glasses had been developed for light bulbs that expanded and contracted in similar amounts, as temperature changed. These made it easy to construct an insulating envelope of glass, while passing connection wires through the glass to the electrodes.
When a vacuum tube is overloaded or operated past its design dissipation, its anode (plate) may glow red. In consumer equipment, a glowing plate is universally a sign of an overloaded tube. However, some large transmitting tubes are designed to operate with their anodes at red, orange, or in rare cases, white heat.
The vacuum inside the envelope must be as perfect, or "hard", as possible. Any gas atoms remaining might be ionized at operating voltages, and will conduct electricity between the elements in an uncontrolled manner. This can lead to erratic operation or even catastrophic destruction of the tube and associated circuitry. Unabsorbed free air sometimes ionizes and becomes visible as a pink-purple glow discharge between the tube elements.
To prevent any remaining gases from remaining in a free state in the tube, modern tubes are constructed with "getters", which are usually small, circular troughs filled with metals that oxidize quickly, with barium being the most common. While the tube envelope is being evacuated, the internal parts except the getter are heated by RF induction heating to extract any remaining gases from the metal. The tube is then sealed and the getter is heated to a high temperature, again by radio frequency induction heating. This causes the material to evaporate, absorbing/reacting with any residual gases and usually leaving a silver-colored metallic deposit on the inside of the envelope of the tube. The getter continues to absorb any gas molecules that leak into the tube during its working life. If a tube develops a crack in the envelope, this deposit turns a white color when it reacts with atmospheric oxygen. Large transmitting and specialized tubes often use more exotic getter materials, such as zirconium. Early gettered tubes used phosphorus based getters and these tubes are easily identifiable, as the phosphorus leaves a characteristic orange or rainbow deposit on the glass. The use of phosphorus was short-lived and was quickly replaced by the superior barium getters. Unlike the barium getters, the phosphorus did not absorb any further gases once it had fired.
Large transmitting tubes have tungsten filaments containing a small trace of thorium. A thin layer of thorium atoms forms on the outside of the wire when heated, serving as an efficient source of electrons. The thorium slowly evaporates from the wire surface, while new thorium atoms diffuse to the surface to replace them. Such thoriated tungsten cathodes deliver lifetimes in the tens of thousands of hours. The claimed record is held by an Eimac power tetrode used in a Los Angeles radio station's transmitter, which was removed from service after 80,000 hours (~9 years) of operation. Transmitting tubes are also claimed to survive lightning strikes more often than transistor transmitters do. For RF power levels above 20 kilowatts, vacuum tubes are commonly more efficient and reliable than similar solid-state circuits.
Cathodes in small "receiving" tubes are coated with a mixture of barium oxide and strontium oxide, sometimes with addition of calcium oxide or aluminium oxide. An electric heater is inserted into the cathode sleeve, and insulated from it electrically by a coating of aluminium oxide. This complex construction causes barium and strontium atoms to diffuse to the surface of the cathode when heated to about 780 degrees Celsius, thus emitting electrons.
The Colossus computer's designer, Dr Tommy Flowers, had a theory that most of the unreliability was caused during power down and (mainly) power up. Once Colossus was built and installed, it was switched on and left switched on running from dual redundant diesel generators (the wartime mains supply being considered too unreliable). The only time it was switched off was for conversion to the Colossus Mk2 and the addition of another 500 or so tubes. Another 9 Colossus Mk2s were built, and all 10 machines ran with a surprising degree of reliability. The 10 Colossi consumed 15 kilowatts of power each, 24 hours a day, 365 days a year—nearly all of it for the tube heaters.
To meet the reliability requirements of the early digital computer Whirlwind, it was necessary to build special "computer vacuum tubes" with extended cathode life. The problem of short lifetime was traced to evaporation of silicon, used in the tungsten alloy to make the heater wire easier to draw. Elimination of the silicon from the heater wire alloy (and paying extra for more frequent replacement of the wire drawing dies) allowed production of tubes that were reliable enough for the Whirlwind project. The tubes developed for Whirlwind later found their way into the giant SAGE air-defense computer system. High-purity nickel tubing and cathode coatings free of materials that can poison emission (such as silicates and aluminium) also contribute to long cathode life. The first such "computer tube" was Sylvania's 7AK7 of 1948. By the late 1950s it was routine for special-quality small-signal tubes to last for hundreds of thousands of hours, if operated conservatively. This reliability made mid-cable amplifiers in submarine cables possible.
Vacuum tubes are less susceptible than corresponding solid-state components to the electromagnetic pulse effect of nuclear explosions. This property kept them in use for certain military applications long after transistors had replaced them elsewhere. Vacuum tubes are still used for very high-powered applications such as microwave ovens, industrial radio-frequency heating, generating large amounts of RF energy for particle accelerators, and power amplification for broadcasting. Many audiophiles, professional audio engineers, and musicians prefer the tube sound of audio equipment based on vacuum tubes over electronics based on transistors. There are companies which still make specialized audio hardware featuring tube technology.
The sound produced by a tube based amplifier with the tubes overloaded (overdriven) is widely used in electric guitar amplification, and has defined the texture of some genres of music such as classic rock and blues. Guitarists often prefer tube amplifiers for the perceived warmth of their tone and the natural compression effect they can apply to an input signal.
In 2002, computer motherboard maker AOpen brought back the vacuum tube for modern computer use by releasing the AX4GE Tube-G motherboard. This motherboard uses a Sovtek 6922 vacuum tube (a version of the 6DJ8) as part of AOpen’s TubeSound Technology. AOpen claims that the vacuum tube brings superior sound.
Various methods of cooling are used to remove generated heat. For low-power dissipation devices the heat is radiated from the anode, which often is blackened on the external surface to assist infrared radiation. Natural air circulation or convection is usually required to keep power tubes from overheating. For larger power dissipation, forced-air cooling (fans) may be required.
From the inception of this technology until the 1950s, the dominant approach to cooling low-power tubes remained aimed at avoiding immediate or very short term failures. For noncritical consumer applications, and in absence of technological alternatives, tube failures did not create major problems for equipment manufacturers, as the cost of tube replacements was borne by end users long accustomed to the experience. Some tubes for the US defense market featured a metal casing, as opposed to glass, and an opaque, black finish that facilitated both heat conduction and radiative cooling. In some highly specialized professional applications where replacement was out of the question, such as undersea cable repeaters, no failures were acceptable. Moreover, as vacuum tube based defence systems became increasingly complex and deployed in ever increasing numbers, it became clear that point failures which were individually easy to diagnose and rectify had a devastating effect on the uptime of systems that contained hundreds of tubes. This resulted in both the creation of special long lasting tubes for projects such as Whirlwind and SAGE, and also in special tube shields that aided heat dispersal and could be retrofitted on existing equipment. These shields act by improving heat conduction from the surface of the tube to the shield itself by means of tens of copper tongues in contact with the glass tube, and have an opaque, black outside finish for improved heat radiation.
High-power tubes in older, large transmitters or power amplifiers are liquid cooled, usually with deionised water for heat transfer to an external radiator, similar to the cooling system of an internal combustion engine. Since the anode is usually the cooled element, the anode voltage appears directly on the cooling water surface, thus requiring the water to be an electrical insulator. Otherwise the high voltage can be conducted through the cooling water to the radiator system; hence the need for deionised water. Such systems usually have a built-in water-conductance monitor which will shut down the high-tension supply (often tens of kilovolts) if the conductance becomes too high. Some very high-power transmitters, such as those used in shortwave broadcasting and VLF communications, use pressurized steam for cooling. Modern transmitters using tubes mainly in the PA section are now largely cooled by forced air through a radiator or other heat-sinking device.
Many of the better tube radios had so-called "tuning eye" indicator tubes behind their front panels, with just the top of the tube showing.
Secondary emission is the term for what happens when electrons in a vacuum strike certain materials, and the impacts cause electrons to be emitted. For some materials, more electrons are emitted than originally hit the surface. Such devices, called electron multipliers, amplify the current represented by the incoming electrons. Several stages (as many as 15 or so) can be cascaded for high gain, and are essential parts of very sensitive phototubes, usually called photomultipliers or multiplier photoubes. The image orthicon TV studio camera tubes also used multistage photomultipliers.
For decades, electron-tube designers tried to use secondary emission to obtain more amplification in vacuum tubes with hot cathodes, but they suffered from short life because the material used for the secondary-emission electrode (called a dynode) "poisoned" the tube's hot cathode. (For instance, the interesting RCA 1630 secondary-emission tube was marketed, but did not last.) However, eventually, Philips of The Netherlands developed the EFP60 tube that had a satisfactory lifetime, and was used in at least one product, a laboratory pulse generator. However, transistors were rapidly improving, and eclipsed tubes in general.
A variant, called a channel electron multiplier, is a curved tube, such as a helix, coated on the inside with material with good secondary emission. One type had a little funnel to capture incoming electrons. The tube was resistive, and its ends were connected to enough voltage to create repeated cascades of electrons.
Tektronix made a high-performance wideband oscilloscope CRT with a channel electron multiplier plate behind the phosphor layer. This plate was a bundled array of a huge number of short individual c.e.m. tubes that accepted a low-current beam and intensified it to provide a display of practical brightness. (The electron optics of the wideband electron gun could not provide enough current to directly excite the phosphor.)
The fluorescent displays commonly used on Videocassette recordera and automotive dashboards are vacuum tubes, using phosphor-coated anodes to form the display characters, and a heated filamentary cathode as an electron source, called "VFDs", or Vacuum Fluorescent Displays. Because the filaments are in view, they must be operated at temperatures where the filament does not glow visibly. These devices are often found in automotive applications, where their high brightness allows reading the display in daylight.
Some tubes, like magnetrons, traveling-wave tubes, carcinotrons, and klystrons, combine magnetic and electrostatic effects. These are efficient (usually narrow-band) RF producers and still find use in radar, microwave ovens and industrial heating. Traveling-wave tubes (TWTs) are very good amplifiers; they are used in some communications satellites. High-powered klystron amplifier tubes can provide hundreds of kW in the UHF range.
Gyrotrons or vacuum masers, used to generate high-power millimetre band waves, are magnetic vacuum tubes in which a small relativistic effect, due to the high voltage, is used for bunching the electrons. Gyrotrons can generate very high powers (hundreds of kW). Free electron lasers, used to generate high-power coherent light and perhaps even X rays, are highly relativistic vacuum tubes driven by high-energy particle accelerators.
Particle accelerators can be considered vacuum tubes that work backward, the electric fields driving the electrons, or other charged particles. In this respect, a cathode ray tube is a particle accelerator.
A tube in which electrons move through a vacuum (or gaseous medium) within a gas-tight envelope is generically called an electron tube.
As of 2008, scores of small companies are manufacturing audiophile amplifiers and preamps that use vacuum tubes.
In the early years of the 21st century there has been renewed interest in vacuum tubes, this time in the form of integrated circuits. The most common design uses a cold cathode field emitter, with electrons emitted from a number of sharp nano-scale tips formed on the surface of a metal cathode.
Their advantages include greatly enhanced robustness combined with the ability to provide high power outputs at low power consumptions. Operating on the same principles as traditional tubes, prototype device cathodes have been constructed with emitter tips formed using nanotubes, and by etching electrodes as hinged flaps (similar to the technology used to create the microscopic mirrors used in Digital Light Processing) that are stood upright by an electrostatic charge.
Such integrated microtubes may find application in microwave devices including mobile phones, for Bluetooth and Wi-Fi transmission, in radar and for satellite communication. Presently they are being studied for possible application to flat-panel display construction.
|Manufacturer||Area of expertise|
|Shuguang Electron Group Co.||Tubes primarily for audio applications|
|Tianjin Quanzhen Electron Tube Technology Co.||Very small manufacturer of high-end audio tubes. Products marketed by Full Music brand.|
|Nanjing Sanle Electronics Co.||Transmitting and industrial tubes, such as 3-500ZG, 4-250A and 4-400C series tube types for used in radio amateur's linear amplifiers and professional broadcasters radio transmitters|
|JiangXi Jingguang Electronics Co.||Ceramic transmitting tubes, some of them marketed by Eimac|
|Huaguang Electric Power & Electronics Co.||Transmitting and industrial tubes, also Chinese made 833C|
|Manufacturer||Area of expertise|
|JSC Expo-pul||Audio tube factory of New Sensor Inc.; Tubes are marketed as Sovtek, Electro Harmonix, Tung-Sol, Mullard and also Svetlana S-marked in USA|
|LLC "Ryazan" Vacuum Components||Russian made SV811 and SV572 series tubes for audio applications and transmitting tubes like 811A, 572B and GU-81, marketed in western countries by Svetlana, Sovtek and Ryazan brands|
|ZAO "SED-SPb" Svetlana Electron Devices, St.Petersburg - JSC Svetlana||"Winged-C" transmitting and audio tubes|
|M.V.S.Z. AO Svetlana - JSC Svetlana||"Winged-C" 300B and EL509 tubes|
|JSC "Voskhod" KRLZ||Tubes for small signal RF and audio applications|
|HC JSC NEVZ-Soyuz||Ceramic transmitting and microwave tubes, (formerly known as Novosibirsk electro-vacuum plant)|
|Manufacturer||Area of expertise|
|Western Electric Inc.||300B triodes|
|Communications & Power Industries Inc.||Eimac and rebuilt Econco high power transmitting tubes|
|Burle Industries Inc.||Industrial and transmitting tubes, formerly factory of RCA|
|MPD Components Inc.||Planar triodes and magnetrons, formerly Ken-Rad and later GE tube factory|
|LND Inc.||Geiger-Mueller tubes|
|Manufacturer||Area of expertise|
|Polyaron GP NPK.||Transmitting tubes, known in western countries as "Poljaron"|
|Manufacturer||Area of expertise|
|Blackburn MicroTech Solutions Ltd.||Small signal tubes, formerly part of Philips-Mullard Blackburn operations.|
|e2v Technologies Ltd.||Transmitting tubes, formerly known as English Electric Valve Co. Ltd.|
|Centronic Ltd.||Geiger-Mueller tubes, formerly Philips GM-tubes|
|Manufacturer||Area of expertise|
|Vacutec GmbH.||Geiger-Mueller tubes|
|Manufacturer||Area of expertise|
|Thales Electron Devices||High power transmitting tubes|
|Manufacturer||Area of expertise|
|Emission Labs||High-end audio tubes|
|KR Audio Electronics s.r.o.||High-end audio tubes|
|Tesla Electrontubes s.r.o.||Transmitting tubes|
|Manufacturer||Area of expertise|
|JJ-Electronic||Primarily for audio applications, factory was formerly part of Tesla Electrontubes|
|Euro Audio Team||Very small manufacturer of high-end audio tubes, products marketed by EAT brand|
|Manufacturer||Area of expertise|
|Thales Lamina Przyrzady Elektronowe Sp.Z.o.o||Microwave tubes for radiolocation equipment, microwave tubes for industrial applications|
Agency Reviews Patent Application Approval Request for "Control Electrode, Charging Device, and Image Forming Apparatus"
Jun 13, 2013; By a News Reporter-Staff News Editor at Politics & Government Week -- Fuji Xerox Co., Ltd. has been issued patent application...
US Patent Issued to Elpida Memory on March 13 for "Semiconductor Device for Supplying Stable Voltage to Control Electrode of Transistor" (Japanese Inventor)
Mar 20, 2012; ALEXANDRIA, Va., March 20 -- United States Patent no. 8,134,858, issued on March 13, was assigned to Elpida Memory Inc. (Tokyo)....
US Patent Issued to Surgelab Korea on July 24 for "Discharge Element with Discharge-Control Electrode and the Control Circuit Thereof" (South Korean Inventor)
Jul 30, 2012; ALEXANDRIA, Va., July 30 -- United States Patent no. 8,227,989, issued on July 24, was assigned to Surgelab Korea (Daejeon, South...
US Patent Issued to Samsung Electronics on Feb. 1 for "Liquid Crystal Display with a Control Electrode Partially Overlapping Slits Forming Domains with a Pixel Electrode and a Protrusion Pattern Providing Higher Position for the Control Electrode Than the Pixel Electrode" (South Korean Inventors)
Feb 04, 2011; ALEXANDRIA, Va., Feb. 4 -- United States Patent no. 7,880,845, issued on Feb. 1, was assigned to Samsung Electronics Co. Ltd....