Different coefficients of thermal expansion can be defined for a substance depending on whether the expansion is measured by:
These characteristics are closely related. The volumetric thermal expansion coefficient can be defined for both liquids and solids. The linear thermal expansion can only be defined for solids, and is common in engineering applications.
Some substances expand when cooled, such as freezing water, so they have negative thermal expansion coefficients.
The thermal expansion coefficient is a thermodynamic property of a substance.
It relates the change in temperature to the change in a material's linear dimensions. It is the fractional change in length per degree of temperature change.
dL = L_{0} x (alpha x dT )
where $L\_0$ is the original length, $L$ the new length, and $T$ the temperature.
The linear thermal expansion is the onedimensional length change with temperature.
The change in area with temperature can be written:
For exactly isotropic materials, the area thermal expansion coefficient is very closely approximated as twice the linear coefficient.
The change in volume with temperature can be written:
The volumetric thermal expansion coefficient can be written
where $T$ is the temperature, $V$ is the volume, $rho$ is the density, derivatives are taken at constant pressure $p$; $beta$ measures the fractional change in density as temperature increases at constant pressure.
Proof:
where $m$ is the mass.
For exactly isotropic materials, the volumetric thermal expansion coefficient is very closely approximated as three times the linear coefficient.
Proof:
This ratio arises because volume is composed of three mutually orthogonal directions. Thus, in an isotropic material, onethird of the volumetric expansion is in a single axis (a very close approximation for small differential changes). Note that the partial derivative of volume with respect to length as shown in the above equation is exact, however, in practice it is important to note that the differential change in volume is only valid for small changes in volume (i.e., the expression is not linear). As the change in temperature increases, and as the value for the linear coefficient of thermal expansion increases, the error in this formula also increases. For nonnegligible changes in volume:
Note that this equation contains the main term, $3L^2$, but also shows a secondary term that scales as $3L\{Delta\; L\}^2\; =\; \{3L^3\}\{alpha\}^2\{Delta\; T\}^2,$, which shows that a large change in temperature can overshadow a small value for the linear coefficient of thermal expansion. Although the coefficient of linear thermal expansion can be quite small, when combined with a large change in temperature the differential change in length can become large enough that this factor needs to be considered. The last term, $\{Delta\; L\}^3$ is vanishingly small, and is almost universally ignored.
In anisotropic materials the total volumetric expansion is distributed unequally among the three axes and if the symmetry is monoclinic or triclinic even the angles between these axes are subject to thermal changes. In such cases it is necessary to treat thermal expansion as a tensor that has up to six independent elements. A good way to determine the elements of the tensor is to study the expansion by powder diffraction.
The expansion and contraction of material must be considered when designing large structures, when using tape or chain to measure distances for land surveys, when designing molds for casting hot material, and in other engineering applications when large changes in dimension due to temperature are expected. The range for α is from 10^{7} for hard solids to 10^{3} for organic liquids. α varies with the temperature and some materials have a very high variation. Some values for common materials, given in parts per million per Celsius degree: (NOTE: This can also be in kelvins as the changes in temperature are a 1:1 ratio)
NOTE: Theoretically, the coefficient of linear expansion can be found from the coefficient of volumetric expansion (β=3α). However, for liquids, α is calculated through the experimental determination of β, hence it is more accurate to state β here than α. (The formula β=3α is usually used for solids)
ApplicationsFor applications using the thermal expansion property, see bimetal and mercury thermometerThermal expansion is also used in mechanical applications to fit parts over one another, e.g. a bushing can be fitted over a shaft by making its inner diameter slightly smaller than the diameter of the shaft, then heating it until it fits over the shaft, and allowing it to cool after it has been pushed over the shaft, thus achieving a 'shrink fit' There exist some alloys with a very small CTE, used in applications that demand very small changes in physical dimension over a range of temperatures. One of these is Invar 36, with a coefficient in the 0.6x10^{6} range. These alloys are useful in aerospace applications where wide temperature swings may occur. External links
ReferencesSee also
