A shear zone or shear is a wide zone of distributed shearing in rock. Typically this is a type of fault but it may be difficult to place a distinct fault plane into the shear zone. Shear zones may form zones of much more intense foliation, deformation, and folding.
Many shear zones host ore deposits as they are a focus for hydrothermal flow through orogenic belts. They may often show some form of retrograde metamorphism from a peak metamorphic assemblage and are commonly metasomatised.
Shear zones can be only inches wide, or up to several kilometres wide. Often, due to their structural control and presence at the edges of tectonic blocks, shear zones are mappable units and form important discontinuities to separate terranes. As such, many large and long shear zones are named, similar to fault systems.
The mechanisms of shearing depend on the pressure and temperature of the rock and on the rate of shear which the rock is subjected to. The response of the rock to these conditions determines how it accommodates the deformation.
Shear zones which occur in more brittle rheological conditions (cooler, less confining pressure) or at high rates of strain, tend to fail by brittle failure; breaking of minerals, which are ground up into a breccia with a milled texture.
Shear zones which occur under brittle-ductile conditions can accommodate much deformation by enacting a series of mechanisms which rely less on fracture of the rock and occur within the minerals and the mineral lattices themselves. Shear zones accommodate compressive stress by movement on foliation planes.
Shearing at ductile conditions may occur by , and dislocation creep within minerals, by fracturing of minerals and growth of sub-grain boundaries, as well as by lattice glide, particularly on platy minerals, especially micas.
Mylonites are essentially ductile shear zones.
During the initiation of shearing, a penetrative planar foliation is first formed within the rock mass. This manifests as realignment of textural features, growth and realignment of micas and growth of new minerals.
The incipient shear foliation typically forms normal to the direction of principal shortening, and is diagnostic of the direction of shortening. In symmetric shortening, objects flatten on this shear foliation much the same way that a round ball of treacle flattens with gravity.
Within assymmetric shear zones, the behavior of an object undergoing shortening is analogous to the ball of treacle being smeared as it flattens, generally into an ellipse. Within shear zones with pronounced displacements a shear foliation may form at a shallow angle to the gross plane of the shear zone. This foliation ideally manifests as a sinusoidal set of foliations formed at a shallow angle to the main shear foliation, and which curve into the main shear foliation. Such rocks are known as L-S tectonites.
If the rock mass begins to undergo large degrees of lateral movement, the strain ellipse lengthens into a cigar shaped volume. At this point shear foliaions begin to break down into a rodding lineation or a stretch lineation. Such rocks are known as L-tectonites.
The sense of shear shown by both S-C and S-C' structures matches that of the shear zone in which they are found.
Other microstructures which can give sense of shear include:
A typical example of a transpression regime is the Alpine Fault zone of New Zealand, where the oblique subduction of the Pacific Plate under the Indo-Australian Plate is converted to oblique strike-slip movement. Here, the orogenic belt attains a trapezoidal shape dominated by oblique splay faults, steeply-dipping recumbent nappes and fault-bend folds.
The Alpine Schist of New Zealand is characterised by heavily crenulated and sheared phyllite. It s being pushed up at the rate of 8 to 10 mm per year, and the area is prone to large earthquakes with a south block up and west oblique sense of movement.
The Hardangerfjord Shear Zone in SW Norway and the North Sea: A Large-Scale Low-Angle Shear Zone in the Caledonian Crust
Jul 01, 2005; Abstract: The Hardangerfjord Shear Zone is a more than 600 km long low-angle extensional structure that affects the South Norway...
Clinopyroxene-Rutile Phyllonites from the East Tenda Shear Zone (Alpine Corsica, France): Pressure-Temperature-Time Constraints to the Alpine Reworking of Variscan Corsica
Nov 01, 2012; Abstract: The East Tenda Shear Zone is the regional structure that marks the Alpine overthrusting of the Ligurian- Piedmontese...
Giant Quartz Vein Formation and High-Elevation Meteoric Fluid Infiltration into the South Armorican Shear Zone: Geological, Fluid Inclusion and Stable Isotope Evidence
Jan 01, 2012; Abstract: Giant quartz veins associated with the South Armorican Shear Zone record important fluid circulation during the...