All cavity magnetrons consist of a hot filament (cathode) kept at, or pulsed to, a high negative potential by a high-voltage, direct-current power supply. The cathode is built into the center of an evacuated, lobed, circular chamber. A magnetic field parallel to the filament is imposed by a permanent magnet. The magnetic field causes the electrons, attracted to the (relatively) positive outer part of the chamber, to spiral outward in a circular path rather than moving directly to this anode. Spaced around the rim of the chamber are cylindrical cavities. The cavities are open along their length and connect the common cavity space. As electrons sweep past these openings, they induce a resonant, high-frequency radio field in the cavity, which in turn causes the electrons to bunch into groups. A portion of this field is extracted with a short antenna that is connected to a waveguide (a metal tube usually of rectangular cross section). The waveguide directs the extracted RF energy to the load, which may be a cooking chamber in a microwave oven or a high-gain antenna in the case of radar.
The sizes of the cavities determine the resonant frequency, and thereby the frequency of emitted microwaves. However, the frequency is not precisely controllable. This is not a problem in many uses such as heating or some forms of radar where the receiver can be synchronized with an imprecise output. Where precise frequencies are needed, other devices such as the Klystron are used. The voltage applied and the properties of the cathode determine the power of the device.
The magnetron is a fairly efficient device. In a microwave oven, for instance, a 1100 watt input will generally create about 700 watts of microwave energy, an efficiency of around 65%. Modern, solid-state, microwave sources at this frequency typically operate at around 25 to 30% efficiency and are used primarily because they can generate a wide range of frequencies. Thus, the magnetron remains in widespread use in roles which require high power, but where precise frequency control is unimportant.
In radar devices the waveguide is connected to an antenna. The magnetron is operated with very short pulses of applied voltage, resulting in a short pulse of microwave energy being radiated. As in all radar systems, the radiation reflected off a target is analyzed to produce a radar map on a screen.
There was an urgent need during radar development in World War II for a high-power microwave generator that worked in shorter wavelengths—around 10 cm (3 GHz) rather than 150 cm—(200 MHz) available from tube-based generators of the time. It was known that a multi-cavity resonant magnetron had been developed in 1935 by Hans Hollmann in Berlin. However, the German military considered its frequency drift to be undesirable and based their radar systems on the klystron instead. It was primarily for this reason that German night fighter radars were not a match for their British counterparts.
In 1940, at the University of Birmingham in the UK, John Randall and Dr. Harry Boot produced a working prototype similar to Hollman's cavity magnetron, but added liquid cooling and a stronger cavity. Randall and Boot soon managed to increase its power output 100 fold. Instead of giving up on the magnetron due to its frequency inaccuracy, they sampled the output signal and synced their receiver to whatever frequency was actually being generated.
Because France had just fallen to the Nazis and Britain had no money to develop the magnetron on a massive scale, Churchill agreed that Sir Henry Tizard should offer the magnetron to the Americans in exchange for their financial and industrial help. By September, the Massachusetts Institute of Technology had set up a secret laboratory to develop the cavity magnetron into a viable radar. Two months later, it was in mass production, and by early 1941, portable airborne radar were being installed into American and British planes. This was codenamed H2S, and was in part developed by Alan Blumlein.
An early 6 kW version, built in England by the GEC Research Laboratories, Wembley, London, was given to the US government in September 1940. It was later described as "the most valuable cargo ever brought to our shores" (see Tizard Mission). At the time the most powerful equivalent microwave producer available in the US (a klystron) had a power of only ten watts. The cavity magnetron was widely used during World War II in microwave radar equipment and is often credited with giving Allied radar a considerable performance advantage over German and Japanese radars, thus directly influencing the outcome of the war.
Short-wave, centimetric radar, which was made possible by the cavity magnetron, allowed for the detection of much smaller objects and the use of much smaller antennas. The combination of the small-cavity magnetron, small antennas, and high resolution allowed small, high quality radars to be installed in aircraft. They could be used by maritime patrol aircraft to detect objects as small as a submarine periscope, which allowed aircraft to attack and destroy submerged submarines which had previously been undetectable from the air. Centimetric contour mapping radars like H2S improved the accuracy of Allied bombers used in the strategic bombing campaign. Centimetric gun-laying radars were likewise far more accurate than the older technology. They made the big-gunned Allied battleships more deadly and, along with the newly developed proximity fuse, made anti-aircraft guns much more dangerous to attacking aircraft. The two coupled together and used by anti-aircraft batteries, placed along the flight path of German V-1 flying bombs on their way to London, are credited with destroying many of the flying bombs before they reached their target.
Since then, many millions of cavity magnetrons have been manufactured; some for radar, but the vast majority for microwave ovens. The use in radar itself has dwindled to some extent, as more accurate signals have generally been needed and developers have moved to klystron and traveling-wave tube systems for these needs.
Among more speculative hazards, at least one in particular is well known and documented. As the lens of the eye has no cooling blood flow, it is particularly prone to overheating when exposed to microwave radiation. This heating can in turn lead to a higher incidence of cataracts in later life. A microwave oven with a warped door or poor microwave sealing can be hazardous.
There is also a considerable electrical hazard around magnetrons, as they require a high voltage power supply. Operating a magnetron with the protective covers removed and interlocks bypassed should therefore be avoided.
Some magnetrons have beryllium oxide (beryllia) ceramic insulators, which is dangerous if crushed and inhaled, or otherwise ingested. Single or chronic exposure can lead to berylliosis, an incurable lung condition. In addition, beryllia is listed as a confirmed human carcinogen by the IARC; therefore, broken ceramic insulators or magnetrons should not be directly handled.
Patent Issued for Method of Forming a Single Common Laser Resonator Cavity and an Optically Segmented Composite Gain Medium
Jul 31, 2013; By a News Reporter-Staff News Editor at Electronics Newsweekly -- From Alexandria, Virginia, VerticalNews journalists report that...
US Patent Issued to Yeda Research and Development on April 26 for "Resonator Cavity Configuration and Method" (Israeli Inventors)
May 03, 2011; ALEXANDRIA, Va., May 3 -- United States Patent no. 7,933,301, issued on April 26, was assigned to Yeda Research and Development...