Phi value analysis
is an experimental protein engineering
method used to study the structure of the folding transition state in small protein domains that fold
in a two-state manner. Since the folding transition state is by definition a transient and partially unstructured state, its structure is difficult to determine by traditional methods such as protein NMR
or X-ray crystallography
. In phi-value analysis, the folding kinetics
and conformational folding stability of the wild-type protein are compared with those of one or more point mutants
. This comparison yields a phi value
(defined below) that seeks to measure the mutated residue's energetic contribution to the folding transition state (and thus the degree of native structure
around the mutated residue in the transition state) from the relative free energies
of the unfolded state, the folded state and the transition state for the wild-type and mutant proteins.
Typically, a high fraction of the protein's residues are mutated one by one to identify clusters of residues that are well-ordered in the folded transition state. The interactions of these residues can be validated using double-mutant-cycle phi analysis, in which the effects of the single mutants are compared with those of the double mutant. In general, the mutations are conservative and replace the original residue with a smaller one (cavity-creating mutations), most commonly alanine; however, others such as tyrosine-to-phenylalanine, isoleucine-to-valine and threonine-to-serine mutations are also used. Examples of proteins that have been studied by phi value analysis include chymotrypsin inhibitor, SH3 domains, individual domains of proteins L and G, ubiquitin, and barnase.
The phi value is defined as:
where represents the energy difference between the transition state and the denatured state for the wild-type protein, represents this energy difference for the mutant protein, and the terms represent the energy difference between the native state and the denatured state. Thus, the phi value represents the ratio of the energetic destabilization introduced by the mutation to the transition state versus that introduced to the native folded state.
The phi value should range from 0 to 1. A phi value of 0 implies that the mutation has no effect on the structure of the rate-limiting transition state on the folding pathway, while a phi value of 1 indicates that the degree to which the transition state is destabilized by the mutation is exactly equal to the degree to which the folded state is destabilized. A phi value near 0 suggests that the region surrounding the mutation is relatively unfolded or unstructured in the transition state, while a value near 1 implies that the local structure around the mutation site in the transition state closely resembles the structure in the native state. It is generally the case that conservative substitutions on the surface of a protein yield phi values near 1. When the phi value is intermediate between 0 and 1, the method cannot directly distinguish between the alternative hypotheses that the transition state is partially structured, or that there are two populations of mostly-unfolded and mostly-folded states.
Phi value analysis fundamentally assumes a close relationship between structure and energy. If the energy landscape
has a well-defined and relatively deep global minimum, the resemblance of a folding intermediate structure to the native state may closely correlate with the energy of that structure. However, if the energy landscape is relatively flat or has many local minima, the relationship may not hold strongly enough for free energy destabilizations to provide useful structural information. The method also assumes that the folding pathway
is not significantly altered, although the folding energies
may be. For nonconservative mutations this assumption might be fundamentally flawed; thus conservative substitutions are preferred, though they may yield smaller energetic destabilizations that are thus more difficult to detect experimentally. Lastly, the restriction of the phi value range as necessarily nonnegative assumes that the introduction of a mutation will not increase the stability and thus lower the energy of either the native or the transition state relative to those of the wild-type protein. Also, it is implicitly assumed that the interactions that stabilize a folding transition state are native-like in nature. Many recent studies of protein folding, however, have suggested that stabilizing non-native interactions in a folding transition state may aid in folding.
pioneered the phi value analysis method by first applying it to the small bacterial
. In conjunction with molecular dynamics
simulations, the analysis illustrated that, at least for this protein, the transition state between folding and unfolding is the same in both reaction directions and more closely resembled the native state. Phi values were found to vary considerably with the location of the mutation, with some regions of the protein yielding values near 0 and others yielding values near 1. The distribution of phi values over the protein agrees well with the simulated unfolding transition state in all but one helix, later identified as folding semi-independently and forming native-like contacts with the remainder of the protein only after the complete transition state has been reached. Such variations in the folding rate within a protein present another challenge in interpreting phi values, since the transition state structure cannot be determined experimentally. Folding and unfolding simulations, though computationally expensive, can provide valuable structural information that complements phi value results.
Variants of -value analysis
Other kinetic-perturbation techniques for analyzing the folding transition state have been developed in recent years. The most well-known variant is the
-value, in which two metal-binding residues such as histidine are engineered into a protein; the folding kinetics are then studied as a function of the metal ion concentration. However, Fersht has illustrated some difficulties with this approach. An alternative "cross-linking" variant of the
-value was developed in the course of studying the association of segments in the folding transition state through the introduction of covalent crosslinks such as disulfide bonds
Errors associated with -value analysis
Experimental errors can be high in measuring equilibrium stability as well the folding/unfolding rates in water for the wild-type protein and mutants. The necessity of extrapolating phi values in pure water from measurements made in solutions containing denaturants
adds uncertainty to the reported values. When the stability difference between the native and mutant protein are low (< 7 kJ/mol), experimental error can be very large; unusual phi-values outside the 0-1 range may arise from these errors rather than illustrating deviations from the conditions assumed by the method. In addition, calculated phi values have been shown to depend strongly on the number of data points collected and the laboratory in which the experiment was performed.