Radar is a system that uses electromagnetic waves to identify the range, altitude, direction, or speed of both moving and fixed objects such as aircraft, ships, motor vehicles, weather formations, and terrain. The term RADAR was coined in 1941 as an acronym for Radio Detection and Ranging. The term has since entered the English language as a standard word, radar, losing the capitalization. Radar was originally called RDF (Radio Direction Finder) in the United Kingdom.
A radar system has a transmitter that emits either microwaves or radio waves that are reflected by the target and detected by a receiver, typically in the same location as the transmitter. Although the signal returned is usually very weak, the signal can be amplified. This enables radar to detect objects at ranges where other emissions, such as sound or visible light, would be too weak to detect. Radar is used in many contexts, including meteorological detection of precipitation, measuring ocean surface waves, air traffic control, police detection of speeding traffic, and by the military.
Several inventors, scientists, and engineers contributed to the development of radar. The first to use radio waves to detect "the presence of distant metallic objects" was Christian Hülsmeyer, who in 1904 demonstrated the feasibility of detecting the presence of a ship in dense fog, but not its distance. He received Reichspatent Nr. 165546 for his pre-radar device in April 1904, and later patent 169154 for a related amendment for ranging. He also received a patent in England for his telemobiloscope on September 22 1904.
Nikola Tesla, in August 1917, first established principles regarding frequency and power level for the first primitive radar units. He stated, "[...] by their [standing electromagnetic waves] use we may produce at will, from a sending station, an electrical effect in any particular region of the globe; [with which] we may determine the relative position or course of a moving object, such as a vessel at sea, the distance traversed by the same, or its speed."
Before the Second World War, developments by the Americans, the Germans, the French, the Soviets and the British led to the modern version of the radar. The year 1934 was particularly busy, the French Émile Girardeau stated he was building a radar system "conceived according to the principles stated by Tesla" and obtained a patent (French Patent n° 788795 in 1934) for a working dual radar system, a part of which was installed on the Normandie liner in 1935. The same year, American Dr. Robert M. Page tested the first monopulse radar and the Soviet military engineer P.K.Oschepkov, in collaboration with Leningrad Electrophysical Institute, produced an experimental apparatus RAPID capable to detect an aircraft in an area with radius of 3 km of a receiver. Hungarian Zoltán Bay produced a working model by 1936 at the Tungsram laboratory in the same vein.
However, it is the British who were the first to fully exploit it as a defence against aircraft attack. This was in fact spurred on by fears that the Germans were developing death rays. Following detailed theoretical study of the possibility of propagating electromagnetic energy and the likely effect, the British scientists asked by the Air Ministry to investigate, concluded that a death ray was impractical but detection of aircraft appeared feasible. Robert Watson-Watt demonstrated to his superiors the capabilities of a working prototype and patented the device in 1935 (British Patent GB593017) It served as the base for the Chain Home network of radars to defend Great Britain. The war precipitated research to find better resolution, more portability and more features for the new defence technology. Post-war years have seen the use of radar in fields as diverse as air traffic control, weather monitoring, astrometry and road speed control.
Electromagnetic waves reflect (scatter) from any large change in the dielectric or diamagnetic constants. This means that a solid object in air or a vacuum, or other significant change in atomic density between the object and what's surrounding it, will usually scatter radar (radio) waves. This is particularly true for electrically conductive materials, such as metal and carbon fiber, making radar particularly well suited to the detection of aircraft and ships. Radar absorbing material, containing resistive and sometimes magnetic substances, is used on military vehicles to reduce radar reflection. This is the radio equivalent of painting something a dark color.
Radar waves scatter in a variety of ways depending on the size (wavelength) of the radio wave and the shape of the target. If the wavelength is much shorter than the target's size, the wave will bounce off in a way similar to the way light is reflected by a mirror. If the wavelength is much longer than the size of the target, the target is polarized (positive and negative charges are separated), like a dipole antenna. This is described by Rayleigh scattering, an effect that creates the Earth's blue sky and red sunsets. When the two length scales are comparable, there may be resonances. Early radars used very long wavelengths that were larger than the targets and received a vague signal, whereas some modern systems use shorter wavelengths (a few centimeters or shorter) that can image objects as small as a loaf of bread.
Short radio waves reflect from curves and corners, in a way similar to glint from a rounded piece of glass. The most reflective targets for short wavelengths have 90° angles between the reflective surfaces. A structure consisting of three flat surfaces meeting at a single corner, like the corner on a box, will always reflect waves entering its opening directly back at the source. These so-called corner reflectors are commonly used as radar reflectors to make otherwise difficult-to-detect objects easier to detect, and are often found on boats in order to improve their detection in a rescue situation and to reduce collisions. For similar reasons, objects attempting to avoid detection will angle their surfaces in a way to eliminate inside corners and avoid surfaces and edges perpendicular to likely detection directions, which leads to "odd" looking stealth aircraft. These precautions do not completely eliminate reflection because of diffraction, especially at longer wavelengths. Half wavelength long wires or strips of conducting material, such as chaff, are very reflective but do not direct the scattered energy back toward the source. The extent to which an object reflects or scatters radio waves is called its radar cross section.
In the common case where the transmitter and the receiver are at the same location, Rt = Rr and the term Rt² Rr² can be replaced by R4, where R is the range. This yields:
This shows that the received power declines as the fourth power of the range, which means that the reflected power from distant targets is very, very small.
The equation above with F = 1 is a simplification for vacuum without interference. The propagation factor accounts for the effects of multipath and shadowing and depends on the details of the environment. In a real-world situation, pathloss effects should also be considered.
Other mathematical developments in radar signal processing include time-frequency analysis (Weyl Heisenberg or wavelet), as well as the chirplet transform which makes use of the fact that radar returns from moving targets typically "chirp" (change their frequency as a function of time, as does the sound of a bird or bat).
In less technical terms, signal-to-noise ratio (SNR), compares the level of a desired signal (such as targets) to the level of background noise. The higher a system's SNR, the better it is in isolating actual targets from the surrounding noise signals.
Noise is also generated by external sources, most importantly the natural thermal radiation of the background scene surrounding the target of interest. In modern radar systems, due to the high performance of their receivers, the internal noise is typically about equal to or lower than the external scene noise. An exception is if the radar is aimed upwards at clear sky, where the scene is so cold that it generates very little thermal noise.
There will be also Flicker noise due to electrons transit, but depending on 1/f, will be much lower than thermal noise when the frequency is high. Hence, in pulse radar, the system will be always heterodyne. See intermediate frequency.
Some clutter may also be caused by a long radar waveguide between the radar transceiver and the antenna. In a typical plan position indicator (PPI) radar with a rotating antenna, this will usually be seen as a "sun" or "sunburst" in the centre of the display as the receiver responds to echoes from dust particles and misguided RF in the waveguide. Adjusting the timing between when the transmitter sends a pulse and when the receiver stage is enabled will generally reduce the sunburst without affecting the accuracy of the range, since most sunburst is caused by a diffused transmit pulse reflected before it leaves the antenna.
While some clutter sources may be undesirable for some radar applications (such as storm clouds for air-defence radars), they may be desirable for others (meteorological radars in this example). Clutter is considered a passive interference source, since it only appears in response to radar signals sent by the radar.
There are several methods of detecting and neutralizing clutter. Many of these methods rely on the fact that clutter tends to appear static between radar scans. Therefore, when comparing subsequent scans echoes, desirable targets will appear to move and all stationary echoes can be eliminated. Sea clutter can be reduced by using horizontal polarization, while rain is reduced with circular polarization (note that meteorological radars wish for the opposite effect, therefore using linear polarization the better to detect precipitation). Other methods attempt to increase the signal-to-clutter ratio.
CFAR (Constant False-Alarm Rate, a form of Automatic Gain Control, or AGC) is a method relying on the fact that clutter returns far outnumber echoes from targets of interest. The receiver's gain is automatically adjusted to maintain a constant level of overall visible clutter. While this does not help detect targets masked by stronger surrounding clutter, it does help to distinguish strong target sources. In the past, radar AGC was electronically controlled and affected the gain of the entire radar receiver. As radars evolved, AGC became computer-software controlled, and affected the gain with greater granularity, in specific detection cells.
Clutter may also originate from multipath echoes from valid targets due to ground reflection, atmospheric ducting or ionospheric reflection/refraction. This specific clutter type is especially bothersome, since it appears to move and behave like other normal (point) targets of interest, thereby creating a ghost. In a typical scenario, an aircraft echo is multipath-reflected from the ground below, appearing to the receiver as an identical target below the correct one. The radar may try to unify the targets, reporting the target at an incorrect height, or - worse - eliminating it on the basis of jitter or a physical impossibility. These problems can be overcome by incorporating a ground map of the radar's surroundings and eliminating all echoes which appear to originate below ground or above a certain height. In newer Air Traffic Control (ATC) radar equipment, algorithms are used to identify the false targets by comparing the current pulse returns, to those adjacent, as well as calculating return improbabilities due to calculated height, distance, and radar timing.
Jamming is problematic to radar since the jamming signal only needs to travel one-way (from the jammer to the radar receiver) whereas the radar echoes travel two-ways (radar-target-radar) and are therefore significantly reduced in power by the time they return to the radar receiver. Jammers therefore can be much less powerful than their jammed radars and still effectively mask targets along the line of sight from the jammer to the radar (Mainlobe Jamming). Jammers have an added effect of affecting radars along other lines of sight, due to the radar receiver's sidelobes (Sidelobe Jamming).
Mainlobe jamming can generally only be reduced by narrowing the mainlobe solid angle, and can never fully be eliminated when directly facing a jammer which uses the same frequency and polarization as the radar. Sidelobe jamming can be overcome by reducing receiving sidelobes in the radar antenna design and by using an omnidirectional antenna to detect and disregard non-mainlobe signals. Other anti-jamming techniques are frequency hopping and polarization. See Electronic counter-counter-measures for details.
One way to measure the distance to an object is to transmit a short pulse of radio signal (electromagnetic radiation), and measure the time it takes for the reflection to return. The distance is one-half the product of round trip time (because the signal has to travel to the target and then back to the receiver) and the speed of the signal. Since radio waves travel at the speed of light (186,000 miles per second or 300,000,000 meters per second), accurate distance measurement requires high-performance electronics.
In most cases, the receiver does not detect the return while the signal is being transmitted. Through the use of a device called a duplexer, the radar switches between transmitting and receiving at a predetermined rate. The minimum range is calculated by measuring the length of the pulse multiplied by the speed of light, divided by two. In order to detect closer targets one must use a shorter pulse length.
A similar effect imposes a maximum range as well. If the return from the target comes in when the next pulse is being sent out, once again the receiver cannot tell the difference. In order to maximize range, one wants to use longer times between pulses, or commonly referred to as a pulse repetition time (PRT), or its inverse, pulse repetition frequency (PRF).
These two effects tend to be at odds with each other, and it is not easy to combine both good short range and good long range in a single radar. This is because the short pulses needed for a good minimum range broadcast have less total energy, making the returns much smaller and the target harder to detect. This could be offset by using more pulses, but this would shorten the maximum range again. So each radar uses a particular type of signal. Long-range radars tend to use long pulses with long delays between them, and short range radars use smaller pulses with less time between them. This pattern of pulses and pauses is known as the pulse repetition frequency (or PRF), and is one of the main ways to characterize a radar. As electronics have improved many radars now can change their PRF thereby changing their range. The newest radars actually fire 2 pulses during one cell, one for short range 10 km / 6 miles and a separate signal for longer ranges 100 km /60 miles.
The distance resolution and the characteristics of the received signal as compared to noise depends heavily on the shape of the pulse. The pulse is often modulated to achieve better performance thanks to a technique known as pulse compression.
Distance may also be measured as a function of time. The Radar Mile is the amount of time it takes for a radar pulse to travel one Nautical Mile, reflect off a target, and return to the radar antenna. Since a Nautical Mile is defined as exactly 1,852 meters, then dividing this distance by the speed of light (exactly 299,792,458 meters per second), and then multiplying the result by 2 (round trip = twice the distance), yields a result of approximately 12.36 microseconds in duration.
This technique can be used in continuous wave radar, and is often found in aircraft radar altimeters. In these systems a "carrier" radar signal is frequency modulated in a predictable way, typically varying up and down with a sine wave or sawtooth pattern at audio frequencies. The signal is then sent out from one antenna and received on another, typically located on the bottom of the aircraft, and the signal can be continuously compared using a simple beat frequency modulator that produces an audio frequency tone from the returned signal and a portion of the transmitted signal.
Since the signal frequency is changing, by the time the signal returns to the aircraft the broadcast has shifted to some other frequency. The amount of that shift is greater over longer times, so greater frequency differences mean a longer distance, the exact amount being the "ramp speed" selected by the electronics. The amount of shift is therefore directly related to the distance traveled, and can be displayed on an instrument. This signal processing is similar to that used in speed detecting Doppler radar. Example systems using this approach are AZUSA, MISTRAM, and UDOP.
A further advantage is that the radar can operate effectively at relatively low frequencies, comparable to that used by UHF television. This was important in the early development of this type when high frequency signal generation was difficult or expensive.
However, if the transmitter's output is coherent (phase synchronized), there is another effect that can be used to make almost instant speed measurements (no memory is required), known as the Doppler effect. Most modern radar systems use this principle in the pulse-doppler radar system. Return signals from targets are shifted away from this base frequency via the Doppler effect enabling the calculation of the speed of the object relative to the radar. The Doppler effect is only able to determine the relative speed of the target along the line of sight from the radar to the target. Any component of target velocity perpendicular to the line of sight cannot be determined by using the Doppler effect alone, but it can be determined by tracking the target's azimuth over time. Additional information of the nature of the Doppler returns may be found in the radar signal characteristics article.
It is also possible to make a radar without any pulsing, known as a continuous-wave radar (CW radar), by sending out a very pure signal of a known frequency. CW radar is ideal for determining the radial component of a target's velocity, but it cannot determine the target's range. CW radar is typically used by traffic enforcement to measure vehicle speed quickly and accurately where range is not important.
A radar has different components:
Early systems tended to use omni-directional broadcast antennas, with directional receiver antennas which were pointed in various directions. For instance the first system to be deployed, Chain Home, used two straight antennas at right angles for reception, each on a different display. The maximum return would be detected with an antenna at right angles to the target, and a minimum with the antenna pointed directly at it (end on). The operator could determine the direction to a target by rotating the antenna so one display showed a maximum while the other shows a minimum.
One serious limitation with this type of solution is that the broadcast is sent out in all directions, so the amount of energy in the direction being examined is a small part of that transmitted. To get a reasonable amount of power on the "target", the transmitting aerial should also be directional.
Parabolic reflectors can be either symmetric parabolas or spoiled parabolas:
Applied similarly to the parabolic reflector, the slotted waveguide is moved mechanically to scan and is particularly suitable for non-tracking surface scan systems, where the vertical pattern may remain constant. Owing to its lower cost and less wind exposure, shipboard, airport surface, and harbour surveillance radars now use this in preference to the parabolic antenna.
Phased array radars have been in use since the earliest years of radar use in World War II, but limitations of the electronics led to fairly poor accuracy. Phased array radars were originally used for missile defense. They are the heart of the ship-borne Aegis combat system, and the Patriot Missile System, and are increasingly used in other areas because the lack of moving parts makes them more reliable, and sometimes permits a much larger effective antenna, useful in fighter aircraft applications that offer only confined space for mechanical scanning.
As the price of electronics has fallen, phased array radars have become more and more common. Almost all modern military radar systems are based on phased arrays, where the small additional cost is far offset by the improved reliability of a system with no moving parts. Traditional moving-antenna designs are still widely used in roles where cost is a significant factor such as air traffic surveillance, weather radars and similar systems.
Phased array radars are also valued for use in aircraft, since they can track multiple targets. The first aircraft to use a phased array radar is the B-1B Lancer. The first aircraft fighter to use phased array radar was the Mikoyan MiG-31. The MiG-31M's SBI-16 Zaslon phased array radar is considered to be the world's most powerful fighter radar Phased-array interferometry or, aperture synthesis techniques, using an array of separate dishes that are phased into a single effective aperture, are not typically used for radar applications, although they are widely used in radio astronomy. Because of the Thinned array curse, such arrays of multiple apertures, when used in transmitters, result in narrow beams at the expense of reducing the total power transmitted to the target. In principle, such techniques used could increase the spatial resolution, but the lower power means that this is generally not effective. Aperture synthesis by post-processing of motion data from a single moving source, on the other hand, is widely used in space and airborne radar systems (see Synthetic aperture radar).
|Band Name||Frequency Range||Wavelength Range||Notes|
|HF||3–30 MHz||10–100 m||coastal radar systems, over-the-horizon radar (OTH) radars; 'high frequency'|
|P||< 300 MHz||1 m+||'P' for 'previous', applied retrospectively to early radar systems|
|VHF||50–330 MHz||0.9–6 m||very long range, ground penetrating; 'very high frequency'|
|UHF||300–1000 MHz||0.3–1 m||very long range (e.g. ballistic missile early warning), ground penetrating, foliage penetrating; 'ultra high frequency'|
|L||1–2 GHz||15–30 cm||long range air traffic control and surveillance; 'L' for 'long'|
|S||2–4 GHz||7.5–15 cm||terminal air traffic control, long-range weather, marine radar; 'S' for 'short'|
|C||4–8 GHz||3.75–7.5 cm||Satellite transponders; a compromise (hence 'C') between X and S bands; weather|
|X||8–12 GHz||2.5–3.75 cm||missile guidance, marine radar, weather, medium-resolution mapping and ground surveillance; in the USA the narrow range 10.525 GHz ±25 MHz is used for airport radar. Named X band because the frequency was a secret during WW2.|
|Ku||12–18 GHz||1.67–2.5 cm||high-resolution mapping, satellite altimetry; frequency just under K band (hence 'u')|
|K||18–24 GHz||1.11–1.67 cm||from German kurz, meaning 'short'; limited use due to absorption by water vapour, so Ku and Ka were used instead for surveillance. K-band is used for detecting clouds by meteorologists, and by police for detecting speeding motorists. K-band radar guns operate at 24.150 ± 0.100 GHz.|
|Ka||24–40 GHz||0.75–1.11 cm||mapping, short range, airport surveillance; frequency just above K band (hence 'a') Photo radar, used to trigger cameras which take pictures of license plates of cars running red lights, operates at 34.300 ± 0.100 GHz.|
|mm||40–300 GHz||7.5 mm – 1 mm||millimetre band, subdivided as below. The frequency ranges depend on waveguide size. Multiple letters are assigned to these bands by different groups. These are from Baytron, a now defunct company that made test equipment.|
|Q||40–60 GHz||7.5 mm – 5 mm||Used for Military communication.|
|V||50–75 GHz||6.0–4 mm||Very strongly absorbed by the atmosphere.|
|E||60–90 GHz||6.0–3.33 mm|
|W||75–110 GHz||2.7 – 4.0 mm||used as a visual sensor for experimental autonomous vehicles, high-resolution meteorological observation, and imaging.|
A klystron tube may also be used as a modulator because it is an amplifier, so it can be modulated by its low power input signal.
The U.S. Navy has instituted a program named Pollution Prevention (P2) to reduce or eliminate the volume and toxicity of waste, air emissions, and effluent discharges. Because of this Coolanol is used less often today.
PAO is a synthetic lubricant composition is a blend of a polyol ester admixed with effective amounts of an antioxidant, yellow metal pacifier and rust inhibitors. The polyol ester blend includes a major proportion of poly (neopentyl polyol) ester blend formed by reacting poly(pentaerythritol) partial esters with at least one C7 to C12 carboxylic acid mixed with an ester formed by reacting a polyol having at least two hydroxyl groups and at least one C8-C10 carboxylic acid. Preferably, the acids are linear and avoid those which can cause odours during use. Effective additives include secondary arylamine antioxidants, triazole derivative yellow metal pacifier and an amino acid derivative and substituted primary and secondary amine and/or diamine rust inhibitor.
A synthetic coolant/lubricant composition, comprising an ester mixture of 50 to 80 weight percent of poly (neopentyl polyol) ester formed by reacting a poly (neopentyl polyol) partial ester and at least one linear monocarboxylic acid having from 6 to 12 carbon atoms, and 20 to 50 weight percent of a polyol ester formed by reacting a polyol having 5 to 8 carbon atoms and at least two hydroxyl groups with at least one linear monocarboxylic acid having from 7 to 12 carbon atoms, the weight percents based on the total weight of the composition.
Radar systems which operate using Ultra Wideband technology can sense a human behind walls. This is possible since the reflective characteristics of humans are generally greater than those of the typical materials used in construction. However, since humans reflect far less radar energy than metal does, these systems require sophisticated technology to isolate human targets and moreover to process any sort of detailed image.
Wipo Publishes Patent of Commissariat a L'energie Atomique et Aux Energies Alternatives for "Millimetre Band Transmitting/ receiving System" (French Inventors)
Sep 27, 2013; GENEVA, Sept. 27 -- Publication No. WO/2013/139939 was published on Sept. 26.Title of the invention: "MILLIMETRE BAND...